Reinco TM7-30 Series Скачать руководство пользователя страница 35

Страница: 35 / 77

MAINTENANCE & SERVICE PAGE 33

MAINTENANCE SCHEDULE

At the end of each job, clean residual materials spilled or over sprayed onto and around the machine. Clean dirt and chaff from
the engine cooling fins and shroud.

FIRST 4 HOURS:

CHECK ENGINE AND ALL MOUNTING BOLTS.
CHECK COUPLING SET SCREWS.
RETORQUE IF LOOSE.
CHECK ENGINE CONTROLS.
CHECK ENGINE FLUID LEVELS.

EVERY 4 HOURS:

CLEAN AIR INTAKE PRECLEANER FOAM.

REPEAT FIRST 4 HOURS INSPECTION.

EVERY 20 HOURS:

INSPECT FLAIL CHAIN AND BLOWER WHEEL.
OIL THE THROTTLE AND CHOKE MECHANISMS.
CLEAN AIR CLEANER PRECLEANER FOAM.
REPEAT THE FIRST 4 HOURS INSPECTION.

EVERY 40 HOURS:

CHECK BATTERY ELECTROLYTES.
CHECK AND SET ENGINE RPM TO 2400 MAXIMUM.

EVERY 100 HOURS:

TUNE UP ENGINE.
CHANGE ENGINE OIL.
REPLACE AIR CLEANER CARTRIDGE.
LUBRICATE BLOWER SHAFT BEARING(S).

DO NOT OVER GREASE BEARINGS!

For specific engine maintenance instructions, please refer to the engine manufacturer's manual.

MANUAL 33000900

© REINCO INC. 1998

REVISED 3/98

Содержание TM7-30 Series














































































Результаты поиска

Содержание TM7-30 Series

Отзывы:

Бренды по названию

Популярные бренды

Reinco TM7-30 Series, Руководство по эксплуатации, частям и обслуживанию

Результаты поиска

Содержание TM7-30 Series

Отзывы:

Бренды по названию

Популярные бренды