manualshive.com logo in svg

Reinco TM7-30 Series, Руководство по эксплуатации, частям и обслуживанию

Поделиться
Скачать
Reinco TM7-30 Series Скачать руководство пользователя страница 25

OPERATION  PAGE 23 

OPTIONAL VACUUM ADAPTER 

Another option adding to the versatility of the 

TM7-30

 Power Mulcher is the Vacuum Adapter kit.  Spilled or over-sprayed 

mulch, leaves and decorative wood chips may be picked up and placed with this easily installed assembly. 

The kit includes a beater drum "inlet hose adapter", and an air "suction cover". 

1  

The inlet hose adapter (A) must be bolted to the 
beater drum side sheet. Be sure the machine is 
turned off and the key is removed before 
attempting assembly. 

2  

Place the tray makeup adaptor (C) onto the tray 
support bars in place of the feed tray. Then secure 
the hose adaptor (A) to the inlet opening. 

3  

The air makeup cover (B) is to be installed on the 
exterior of the unit at the pillow block bearing end. 
Remove the bearing shaft guard. Hold the cover 
over the beater shaft with the "U" shaped notch 
facing down. Slide the piece towards the beater 
shaft and wedge it between the beater drum wall 
and the bearing until firmly secured. This cover 
now forces all make-up air to be drawn through 
the inlet hose adapter. Replace the bearing guard 
using the two longer bolts supplied with the 
vacuum kit. 

4  

The final installation step involves installing 
suction and discharge hoses consistent with the 
desired application. Typically, the basic hose 
"starter kit" (S) would be connected to the inlet 
adapter by slipping the hose over the adapter tube 
and clamping the hose as indicated in the forgoing 
section. The other end of the hose would utilize 
the discharge spout end as a suction head. Other 
extension hoses may be added on the suction and 
discharge loops as the individual job dictates, 
however, the length of the hoses used will be 
constrained by the type of material(s) being 
vacuumed. 

TM7-30 VACUUM KIT 

A 

B 

C 

E 

S 

PN: 33009300 - VACUUM KIT 

The feed man is now utilized to pick up the desired material by working the pick up end of the hose. Compacted or wetted 
material should be kicked up to assist in vacuuming. The placement operator simply directs the discharge boom assembly or the 
discharge extension hose (E) if utilized. 

CAUTION !  

DO NOT ATTEMPT TO PICK UP OR  DISCHARGE ROCKS, NAILS, OR OTHER 
DEBRIS WHICH MAY DAMAGE BLOWER OR CAUSE PREMATURE WEAR. 

When done with the job, turn the machine off and remove the adapter assembly and suction cover. Clean out any residual 
material remaining in the beater drum, then replace the feed tray. 

MANUAL 33000900 

© REINCO INC. 1998 

REVISED 3/98 

Содержание TM7-30 Series














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды