manualshive.com logo in svg

Reinco TM7-30 Series, Руководство по эксплуатации, частям и обслуживанию

Поделиться
Скачать
Reinco TM7-30 Series Скачать руководство пользователя страница 24

CLEAN-UP

After use, the system must be flushed. Fuel oil or cutback waste oil should be used for this purpose.

Here are the steps to follow:

1

Remove pick-up tube from the asphalt and drain into a 5 gallon container of flushing liquid.

2

Place a piece of waste hose onto the boom nozzle and return to the container.

3

Start engine. Make certain valve is open, engage clutch and run at a slow idle for about 5 minutes.

4

Close boom valve, replace pick-up tube in holder, disengage clutch and turn engine off.

5

Any excess coating should be wiped clean with fuel oil.

6

Remove strainer element and clean before replacing.

If emulsified asphalt is used, flush the pump and spray hose with fuel oil or with a 50/50 oil kerosene mix.

If water based tackifiers are used, flush system with clean water making particularly certain the strainer is unclogged. Follow the
water flush with a 50/50 oil kerosene mix.

OPTIONAL EXTENSION HOSE(S)

Up to 100 feet of 8" flexible extension hose can be used to apply mulch in hard to reach areas. 

To install hose:

1

Install the hose adaptor (A) onto the
discharge boom end. Locate and bolt the
mounting angles to the boom. Some
drilling will be required for feild
installation. Secure the boom adaptor to
the mounting angles with the hardware
provided.

2

Lock the boom in the transport position
to insure that the discharge assembly is
directed away from the engine.

3

Place a stainless band clamp (B) over
the hose end and mount the hose to the
boom adaptor end (A). Tighten
band clamp.

4

Install the applicator spout end (C)
similarly.

5

If additional extension hoses are being
used, they may be inserted before the
applicator spout by means of a coupling
tube (D),
hose kit. The hose ends are to be
clamped over the coupler.

Mulching can now be started. Adjust throttle to desired speed and begin feeding untied mulch bales while the placement operator
directs the discharge at the hose end.

TM7-30 EXTENSION HOSE KITS

A

B

C

D

PN: 33009110 -

PN: 33009200 -

( R e f .   p g   6 9 )

PAGE 22

  REINCO TM7-30   SAFETY OPERATION PARTS AND SERVICE MANUAL

MANUAL 33000900

© REINCO INC. 1998

REVISED 3/98

the

included with each extension

25 FOOT STARTER KIT

25 FOOT EXTENSION KIT

Содержание TM7-30 Series














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды