Rehabed LEO Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 56

Rehabed LEO Скачать руководство пользователя страница 21

21

▪

Prepare the dome head screws and the
Ericson nuts.

▪

Place the Ericson nuts in the holes from the
inside of the mattress platform (3 pcs.) in the
place where the side rail will be fitted.

▪

Prepare a side rail and place it on the
mattress platform.

▪

Note: the side rails are available in the right
or left and long or short version!

Make sure

that the side rail release button (shown
below) is closer to the center of the mattress
platform.

▪

Use the dome screws and fix the side rail to the bed.

▪

Repeat the above steps for the other side rails.

▪

If there is any doubt about the assembly contact the provider
or manufacturer, incorrectly fitted side rails can lead to
death.

▪

Side rails must be installed on both sides of the bed (on the
side of the wall as well).

▪

With standard side rails, the maximum height of the mattress
is 150 mm.

▪

In case of damage to the rails (bending, breaking, cracking
etc.), they should be immediately replaced with new ones
due to the risk of an accident.

«
...
19
20
21
22
23
...
»

Содержание LEO

























































Отзывы:

Нет отзывов