background image

4

 | 

Hampton® H200 Cast Freestanding Woodstove

 | 

4

safety decal

This is a copy of the label that accompanies 

each Hampton H200 Freestanding Woodstove. 

We have printed a copy of the contents here 

for your review.

NOTE:

 Hampton units are constantly being 

improved. Check the label on the unit and if 

there is a difference, the label on the unit is the 

correct one.

HOT WHILE IN OPERATION DO NOT TOUCH.  KEEP CHILDREN,

CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE

SKIN BURNS. READ NAMEPLATE AND INSTRUCTIONS.

ATTENTION

SURFACES CHAUDES DURANT LE FONCTIONNEMENT.

NE PAS TOUCHER. TENIR LES ENFANTS, LES VÊTEMENTS

ET LES MEUBLES ÉLOIGNÉS DE L'APPAREIL. 

TOUT CONTACT PEUT CAUSER DES BRÛLURES. LIRE LA PLAQUE SIGNALÉTIQUE

ET LES INSTRUCTIONS.

DO NOT REMOVE THIS LABEL/

 NE PAS RETIRER CETTE ÉTIQUETTE

290

MADE IN CANADA / FABRIQUÉ AU CANADA

CAUTION

918-428c  

LISTED SPACE HEATER, SOLID FUEL TYPE,  ALSO 

SUITABLE FOR MOBILE HOME INSTALLATION / 

APPAREIL DE CHAUFFAGE AMBIANT HOMOLOGUÉ 

À COMBUSTIBLE SOLIDE, CONVENANT AUSSI

POUR INSTALLATION DANS UNE MAISON MOBILE

 

MODEL:  HAMPTON  CAST FREESTANDING WOOD STOVE -  H200

MODÈLE : POÊLE À BOIS AUTOPORTANT EN FONTE HAMPTON - H200

TESTED TO: UL-1482 / ULC-S627-00   REPORT NO: 219-S-09-2

INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS.  

CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.  

USE 150 MM (6 IN.) DIAMETER MINIMUM 24 MSG BLACK OR 26 MSG BLUED STEEL CONNECTOR WITH LISTED UL103 HT 

FACTORY-BUILT CHIMNEY SUITABLE FOR USE WITH SOLID FUELS OR MASONRY CHIMNEY.  

SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED FOR PASSING A 

CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING.  DO NOT PASS CHIMNEY CONNECTOR THROUGH COMBUSTIBLE 

WALL OR CEILING.  DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

INSTALLER ET UTILISER SEULEMENT SELON LES CONSIGNES D’INSTALLATION ET D’UTILISATION DU FABRICANT. 

CONTACTER LES RESPONSABLES DU BÂTIMENT OU DU SERVICE-INCENDIE DE VOTRE RÉGION POUR CONNAÎTRE 

LES RESTRICTIONS ET EXIGENCES D’INSPECTION DANS VOTRE RÉGION. UTILISER UN CONNECTEUR D’UN DIAMÈTRE 

MINIMAL DE 150 MM (6 PO) 24 MSG EN ACIER NOIR OU 26 MSG EN ACIER BRONZÉ AVEC CHEMINÉE PRÉFABRIQUÉE 

HOMOLOGUÉE UL103 HT CONÇUE POUR UTILISATION AVEC COMBUSTIBLES SOLIDES OU UNE CHEMINÉE DE MAÇON-

NERIE.

VOIR LE CODE DU BÂTIMENT LOCAL ET LES INSTRUCTIONS DU FABRICANT CONCERNANT LES PRÉCAUTIONS  EXI-

GÉES POUR INSTALLER UNE CHEMINÉE TRAVERSANT UN MUR OU PLAFOND EN MATÉRIAUX COMBUSTIBLES. NE PAS 

FAIRE TRAVERSER LE CONNECTEUR DE CHEMINÉE DANS UN MUR OU PLAFOND EN MATÉRIAUX COMBUSTIBLES. NE 

PAS RACCORDER CE POÊLE À BOIS À UN CONDUIT DE CHEMINÉE DESSERVANT UN AUTRE APPAREIL.

MINIMUM ALCOVE CEILING HEIGHT: 1.5 M / 5 FT         MAXIMUM ALCOVE DEPTH 1220 MM / 48 IN.    

MINIMUM CLEARANCES FOR HORIZONTAL CONNECTOR TO CEILING: 457 MM / 18"

THE SPACE BENEATH THE HEATER MUST NOT BE OBSTRUCTED. OPERATE ONLY WITH FIREBRICKS IN PLACE.

FOR USE WITH SOLID WOOD FUEL ONLY.  USE OF OTHER FUELS MAY DAMAGE HEATER AND CREATE A HAZARDOUS 

CONDITION.  DO NOT OBSTRUCT COMBUSTION AIR OPENINGS.  OPERATE ONLY WITH FIREBRICKS IN PLACE.  OPERATE 

ONLY WITH DOOR CLOSED - OPEN FEED DOOR TO FEED FIRE ONLY.  DO NOT USE GRATE OR ELEVATE FIRE.  BUILD WOOD 

FIRE DIRECTLY ON HEARTH.  DO NOT OVERFIRE - IF HEATER OR CHIMNEY CONNECTOR GLOWS YOU ARE OVERFIRING.  

INSPECT  AND  CLEAN  CHIMNEY  AND  CONNECTOR  FREQUENTLY.    UNDER  CERTAIN  CONDITIONS  OF  USE  CREOSOTE 

BUILDUP MAY OCCUR RAPIDLY.  KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL AWAY FROM HEATER.  REPLACE 

GLASS ONLY WITH NEOCERAM GLASS. COMBUSTIBLE FLOOR MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL 

EXTENDING BENEATH THE HEATER AND TO THE FRONT AND SIDES AS INDICATED OR TO THE NEAREST PERMITTED 

COMBUSTIBLE MATERIAL.

OPTIONAL COMPONENT: FAN (846-515), ELECTRICAL RATING: VOLTS 115, 60 HZ, 2 AMPS

DANGER: RISK OF ELECTRIC SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT. DO NOT ROUTE POWER CORD 

UNDER OR IN FRONT OF APPLIANCE.

MINIMUM ALCOVE CEILING HEIGHT: 1.5 M / 5 FT         MAXIMUM ALCOVE DEPTH 1220 MM / 48 IN.    

MINIMUM CLEARANCES FOR HORIZONTAL CONNECTOR TO CEILING: 457 MM / 18"

THE SPACE BENEATH THE HEATER MUST NOT BE OBSTRUCTED. OPERATE ONLY WITH FIREBRICKS IN PLACE.

FOR USE WITH SOLID WOOD FUEL ONLY.  USE OF OTHER FUELS MAY DAMAGE HEATER AND CREATE A HAZARDOUS 

CONDITION.  DO NOT OBSTRUCT COMBUSTION AIR OPENINGS.  OPERATE ONLY WITH FIREBRICKS IN PLACE.  OPERATE 

ONLY WITH DOOR CLOSED - OPEN FEED DOOR TO FEED FIRE ONLY.  DO NOT USE GRATE OR ELEVATE FIRE.  BUILD WOOD 

FIRE DIRECTLY ON HEARTH.  DO NOT OVERFIRE - IF HEATER OR CHIMNEY CONNECTOR GLOWS YOU ARE OVERFIRING.  

INSPECT  AND  CLEAN  CHIMNEY  AND  CONNECTOR  FREQUENTLY.    UNDER  CERTAIN  CONDITIONS  OF  USE  CREOSOTE 

BUILDUP MAY OCCUR RAPIDLY.  KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL AWAY FROM HEATER.  REPLACE 

GLASS ONLY WITH NEOCERAM GLASS. COMBUSTIBLE FLOOR MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL 

EXTENDING BENEATH THE HEATER AND TO THE FRONT AND SIDES AS INDICATED OR TO THE NEAREST PERMITTED 

COMBUSTIBLE MATERIAL.

OPTIONAL COMPONENT: FAN (846-515), ELECTRICAL RATING: VOLTS 115, 60 HZ, 2 AMPS

DANGER: RISK OF ELECTRIC SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT. DO NOT ROUTE POWER CORD 

UNDER OR IN FRONT OF APPLIANCE.

COMPONENTS REQUIRED FOR MOBILE HOME INSTALLATION: OUTSIDE AIR KIT AND ONE OF THE FOLLOWING DOUBLE 

WALL CONNECTOR

IN CANADA: LISTED SECURITY MODEL DP, OR OLIVER MACLEOD PRO-VENT PV DOUBLE WALLED CONNECTOR WITH  

LISTED CHIMNEY SYSTEM: SECURITY MODEL S2100, ICC EXCEL 2100, SUPER VENT 2100, SUPERPRO 2100, CF SENTINAL.

IN USA:   LISTED DOUBLE WALL CONNECTORS SECURITY MODEL DP, SELKIRK MODEL DS, OLIVER MACLEOD PRO VENT 

PV, SIMPSON DURA VENT MODEL DVL, GSW SUPER PIPE 6, METAL-FAB DOUBLE WALL.  CONNECTED TO ONE OF THE 

FOLLOWING COMPATIBLE CHIMNEY SYSTEMS SECURITY MODEL S2100 OR MODEL ASHT, SELKIRK MODEL SSII, OLIVER 

MACLEOD  PRO  JET  3103,  SIMPSON  DURA  PLUS,  GSW  MODEL  SC  OR  METAL-FAB  TEMP/GUARD, AMERI-TECHS,   ICC 

EXCEL 2100, SIMPSON DURA PLUS HTC .  USE CHIMNEY COMPONENTS AS SPECIFIED IN INSTALLATION INSTRUCTIONS. 

HAUTEUR MIN. DU PLAFOND DE L’ALCÔVE : 1,5 M / 5 PI.  

PROFONDEUR MAX. DE L’ALCÔVE : 1220 MM / 48 PO.

DÉGAGEMENT MINIMAL DU PLAFOND POUR UN CONNECTEUR HORIZONTAL : 457 MM / 18 PO.

L’ESPACE AU-DESSOUS DU POÊLE NE DOIT PAS ÊTRE OBSTRUÉ. UTILISER SEULEMENT AVEC LES BRIQUES RÉFRACTAIRES 

EN PLACE.

À UTILISER AVEC DU BOIS SOLIDE SEULEMENT. L’UTILISATION D’AUTRES COMBUSTIBLES PEUT ENDOMMAGER LE POÊLE 

ET  S'AVÉRER  DANGEREUSE.  NE  PAS  OBSTRUER  LES  OUVERTURES  D’AIR  DE  COMBUSTION.  UTILISER  SEULEMENT 

AVEC LES BRIQUES RÉFRACTAIRES EN PLACE. UTILISER SEULEMENT AVEC LA PORTE FERMÉE – OUVRIR LA PORTE 

DE CHARGEMENT SEULEMENT POUR ALIMENTER LE FEU. NE PAS UTILISER DE GRILLE À BÛCHES NI SURÉLEVER LE 

FEU. MONTER LE FEU DE BOIS DIRECTEMENT SUR L’ÂTRE. NE PAS SURCHAUFFER – SI LE POÊLE OU LE CONNECTEUR 

DE CHEMINÉE SE MET À ROUGIR, C'EST LE SIGNE D'UNE SURCHAUFFE. INSPECTER ET NETTOYER FRÉQUEMMENT LA 

CHEMINÉE ET LE CONNECTEUR. DANS CERTAINES CONDITIONS D’UTILISATION, UN DÉPÔT DE CRÉOSOTE PEUT SE FORMER 

RAPIDEMENT. TENIR LES MEUBLES ET AUTRES MATÉRIAUX COMBUSTIBLES ÉLOIGNÉS DU POÊLE. REMPLACER LA VITRE 

SEULEMENT PAR DU VERRE EN NEOCERAM. LE PLANCHER COMBUSTIBLE DOIT ÊTRE PROTÉGÉ PAR DES MATÉRIAUX 

NON COMBUSTIBLES DÉPASSANT AU-DESSOUS, À L'AVANT ET SUR LES CÔTÉS DU POÊLE, TEL QU’INDIQUÉ, OU JUSQU’AU 

MATÉRIAU COMBUSTIBLE LE PLUS PROCHE PERMIS.

COMPOSANTS EN OPTION : VENTILATEUR (846-515), ALIMENTATION ÉLECTRIQUE : 115 VOLTS, 60 HZ, 2 AMP.

DANGER : RISQUE D’ÉLECTROCUTION. DÉCONNECTER L’ALIMENTATION ÉLECTRIQUE AVANT DE FAIRE L’ENTRETIEN DU 

POÊLE. NE PAS INSTALLER LE CORDON ÉLECTRIQUE SOUS OU DEVANT L’APPAREIL.

COMPOSANTS EXIGÉS POUR INSTALLATION DANS UNE MAISON MOBILE : KIT DE PRISE D’AIR EXTÉRIEUR ET UN DES 

CONNECTEURS DE CHEMINÉE À DOUBLE PAROI SUIVANTS :

AU CANADA : CONNECTEURS DE CHEMINÉE HOMOLOGUÉS À DOUBLE PAROI : SECURITY MODÈLE DP, OU OLIVER MACLEOD 

PRO-VENT PV, AVEC SYSTÈME DE CHEMINÉE HOMOLOGUÉ : SECURITY MODÈLE S2100, ICC EXCEL 2100, SUPER VENT 

2100, SUPERPRO 2100, CF SENTINAL.

AUX ÉTATS-UNIS : CONNECTEURS DE CHEMINÉE HOMOLOGUÉS À DOUBLE PAROI : SECURITY MODÈLE DP, SELKIRK 

MODEL DS, OLIVER MACLEOD PRO VENT PV, SIMPSON DURA VENT MODÈLE DVL, GSW SUPER PIPE 6, METAL-FAB À 

DOUBLE PAROI. CONNECTÉ À L’UN DES SYSTÈMES DE CHEMINÉE COMPATIBLES SUIVANTS : SECURITY MODÈLE S2100 

OU MODÈLE ASHT, SELKIRK MODÈLE SSII, OLIVER MACLEOD PRO JET 3103, SIMPSON DURA PLUS, GSW MODÈLE SC OU 

METAL-FAB TEMP/GUARD, AMERI-TECHS, ICC EXCEL 2100, SIMPSON DURA PLUS HTC. UTILISER LES COMPOSANTS DE 

CHEMINÉE SPÉCIFIÉS DANS LES INSTRUCTIONS D’INSTALLATION.

MANUFACTURED BY/ FABRIQUÉ PAR :

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.

6988 VENTURE ST.

DELTA, BC  V4G 1H4

290

MINIMUM CLEARANCES TO

COMBUSTIBLE MATERIALS

DÉGAGEMENTS MINIMAUX 

DES MATÉRIAUX COMBUSTIBLES

RESIDENTIAL INSTALLATION USING

 SINGLE WALL  CONNECTOR

INSTALLATION RÉSIDENTIELLE UTILISANT

UN CONNECTEUR À SIMPLE PAROI

SIDEWALL  A 431  mm / 17 in  D 737 mm / 29 in

BACKWALL  B 381  mm / 15 in  E  435 mm / 17-1/8 in

CORNER 

C 330  mm / 13 in  F  505 mm / 19-7/8 in

MUR LATÉRAL 

MUR ARRIÈRE

COIN 

MUR LATÉRAL 

MUR ARRIÈRE

COIN 

MUR LATÉRAL 

MUR ARRIÈRE

COIN 

MUR LATÉRAL 

MUR ARRIÈRE

 

A 431mm/17po

B 381mm/15po

C 330mm/13po

A 381mm/15po

B 254mm/10po

C 228mm/9po

A 381mm/15po

B 254mm/10po

C 228mm/9po

G 381mm/15po

H 330mm/13po

D 737mm/29po

E 435mm/17-1/8po

F 505mm/19-7/8po

D 686mm/27po

E 308mm/12-1/8po

F 403mm/15-7/8po

D 686mm/27po

E 308mm/12-1/8po

F 403mm/15-7/8po

I  686mm/27po

J 384mm/15-1/8po

INSTALLATION USING LISTED DOUBLE WALL 

CONNECTOR - ALCOVE

INSTALLATION UTILISANT UN CONNECTEUR

HOMOLOGUÉ À DOUBLE PAROI - ALCÔVE

INSTALLATION USING LISTED DOUBLE WALL 

CONNECTOR -  MOBILE HOME 

INSTALLATION UTILISANT UN CONNECTEUR

HOMOLOGUÉ À DOUBLE PAROI - MAISON MOBILE 

SIDEWALL  A 381  mm / 15 in  D 686 mm / 27 in

BACKWALL  B 254  mm / 10 in  E 308 mm / 12-1/8 in

CORNER 

C 228  mm / 9 in 

F 403 mm / 15-7/8 in 

SIDEWALL  A 381 mm / 15  in  D 686 mm / 27 in

BACKWALL  B 254  mm / 10 in  E 308 mm / 12-1/8 in

CORNER 

C 228  mm / 9 in 

F 403 mm / 15-7/8 in 

INSTALLATION USING LISTED DOUBLE WALL 

CONNECTOR - RESIDENTIAL CLOSE CLEARANCE

INSTALLATION UTILISANT UN CONNECTEUR HOMO-

LOGUÉ À DOUBLE PAROI - RÉSIDENTIEL

(DÉGAGEMENT RÉDUIT)

FLOOR 

PROTECTION*

PROTECTION DE 

PLANCHER*

MEASURE 

     

  

      FLUE

FROM  

        HEATER    

       CENTER-LINE

MESURES 

                        

DU CENTRE DU   

À PARTIR 

      DU POÊLE     

 CONDUIT DE CHEMINÉE        

SIDEWALL  G 381 mm / 15 in  I  686 mm / 27 in

BACKWALL  H 330 mm / 13 in  J  384 mm / 15-1/8 in

*  In  Canada,  fl oor  protection  must extend  18"  (457mm)  to 
the front and 8" (200mm) to each side and back of the stove.

* Au Canada, la protection de plancher doit dépasser de 18 
po (457 mm) à l’avant et de 8 po (200 mm) de chaque côté 
du poêle et derrière le poêle.

K  457 mm  /  18 in

L  150 mm  /  6 in

M  150 mm  /  6 in

 JAN    FEB    MAR     

APR     MA

  JUN     JUL

    

AUG    SEPT   OCT   NOV     DE

C

DA

TE OF MANUF

ACTURE

2018

2017

2020

202

1

201

9

Содержание H200













































Отзывы: