Regency City Series CB40E-LP Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 100

background image

City Series

|

25

installation

WRROWLS

The compact panel kit is used in conjunction with the compact framing kit.
Install the compact framing kit before installing the panels.

Note:

The minimum ceiling height must be 8 feet for the compact framing kit

and compact wood panel kit to fi t this particular application.
The compact framing kit when assembled must be set to a predetermined
overall height of 93 inches from fi nished fl oor to the top of the framing kit.

1. Install the front lower panel fi rst, line up the screws on the back of the panel

with the keyholes on the framing kit.

2. Hang the panel by matching the screws at the back of the panel to the

corresponding keyholes and lower the panel until the screws rest at the
bottom of each keyhole.

3. Install the left and right lower side panels using the same procedure as

the front panel.

4. Reach inside the framing kit and tighten the screws on the panels to eliminate

any movement or shifting of the panels—once installed.

NOTE: After installation, ensure all three lower panels are at the same level
at the bottom. Also ensure that the side panels are sitting exactly at 90

º

and

not tilting inward or outward as the correct installation of the middle and top
panels depends on proper installation of the lower panels. Adjust panels as
needed until side and front panels are level.

Tighten screws from

inside framing

Keyhole on

framing unit

Close up of screw in

keyhole

Screw at back of panel

Ensure ﬁ rst row of panels (front + sides) are even with one another

Optional compact wood panel kit Installation CB40E

«
...
23
24
25
26
27
...
»

Содержание City Series CB40E-LP





































































































Отзывы:

Нет отзывов

Похожие инструкции для City Series CB40E-LP

Бренд: Rinnai Страницы: 21

Бренд: Pacific energy Страницы: 24

Бренд: IHP Страницы: 4

Бренд: Valor Страницы: 12

Бренд: Sylvania Страницы: 6

Бренд: C3 Страницы: 2

L-CM057PST-B-CA

Бренд: Sunjoy Страницы: 4

Бренд: Riello Страницы: 44

Бренд: barbas Страницы: 44

Бренд: Monessen Hearth Страницы: 1

Бренд: Obadiah Страницы: 5

Бренд: MHSC Страницы: 24

739CLK Classic Log Kit

Бренд: Valor Страницы: 4

Бренд: UBERHAUS DESIGN Страницы: 9

New York Corner

Бренд: Nordpeis Страницы: 20

Бренд: Empire Comfort Systems Страницы: 2

Бренд: HAMPTON BAY Страницы: 23

Бренд: Vanguard Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды