Regency City Series CB40E-LP Скачать руководство пользователя страница 73

Страница: 73 / 100

City Series

maintenance

CB40E enamel panel installation

1. Turn off unit and allow to cool to room temperature. Remove the outer safety

glass and inner glass — see manual for instructions.

Back Panel

Panel Clips

4. Install back enamel panel - manoeuvre panel into unit and position panel

at back wall of irebox.

2. Install inner irebox base panel.

7. Install outer irebox base panel.

6. Install inner safety glass-see manual.

Black Enamel Panels — Handling Instructions

•

Black Enamel panels must be inspected for scratches and dimples prior to installation.

All claims to be recorded at this time.
Claims for damage after installation will not receive consideration.

•

Black Enamel panels will discolor a little during normal operation. This is normal and should not be considered a defect.

All hand and inger marks

MUST

be cleaned off with a soft cloth. Use an ammonia based cleaner (ie. glass cleaner) to remove any ingerprints before

applying heat to the unit.

Failure to do this will result in burn stain on panels which you will be unable to remove.

*Not protected by product warranty.

5. Secure panel with 2 panel clips and 2 screws.

8. Install 2 outer side panels.

3. Install panel clips into the slots at the top of the panel as shown.

Содержание City Series CB40E-LP





































































































Результаты поиска

Содержание City Series CB40E-LP

Отзывы:

Похожие инструкции для City Series CB40E-LP

Бренды по названию

Популярные бренды

Regency City Series CB40E-LP, Инструкция для владельца и по установке

Результаты поиска

Содержание City Series CB40E-LP

Отзывы:

Похожие инструкции для City Series CB40E-LP

Бренды по названию

Популярные бренды