Regency City Series CB40E-LP Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 100

background image

28

|

City Series

installation

Keyhole on

framing unit

Right side panel facing unit

Left side panel facing unit

Front middle panel

Bottom Cover

Close up of screw in

keyhole

Screw at back of panel

The extended wood panel kit is used in conjunction with the extended framing
kit. Install the extended framing kit before installing the panels.

Note: The minimum ceiling height must be 8 feet for the extended framing kit
and extended wood panel kit to fi t this particular application. The extended
framing kit when assembled must be set to a predetermined overall height of
93 inches from fi nished fl oor to the top of the framing kit.

1. Install the front lower panel fi rst, line up the screws on the back of the panel

with the keyholes on the framing kit.

2 Hang the panel by matching the screws at the back of the panel to the cor-

responding keyholes and lower the panel until the screws rest at the bottom
of each keyhole.

3. Install the left and right lower side panels using the same procedure as

the front panel.

NOTE: After installation, ensure all three lower panels are at the same level
at the bottom. Also ensure that the side panels are sitting exactly at 90º and
not tilting inward or outward as the correct installation of the middle and top
panels depends on proper installation of the lower panels. Adjust panels as
needed until side and front panels are level.

NOTE: If the side panels sit lower than the front panel the bottom cover on the
side may be adjusted to correct this issue.
Loosen the 2 screws in locations shown below, push bottom panel up and
retighten screws.

Ensure fi rst row of panels (front + sides) are even with one another

4. Install the front middle panel, position the brackets at the bottom of the front

middle panel in behind the front lower panel.

5. Tighten the screws at the back of the front middle panel.

/RRVHQVFUHZV

Optional extended wood panel kit Installation CB40E

«
...
26
27
28
29
30
...
»

Содержание City Series CB40E-LP





































































































Отзывы:

Нет отзывов

Похожие инструкции для City Series CB40E-LP

CANTERBURY CANTIB-02-LP

Бренд: Cannon Страницы: 12

Бренд: FireplaceXtrordinair Страницы: 38

Бренд: Twin-Star International Страницы: 28

Бренд: ORTAL Страницы: 17

Бренд: Riello Страницы: 48

Leveling Leg Field Fix Kit MPE-27

Бренд: Lennox Hearth Products Страницы: 1

Intermittent Pilot ADVCX36FP70N-2

Бренд: American Hearth Страницы: 68

Colorado Mesh Chimenea XL

Бренд: La Hacienda Страницы: 4

Бренд: Coleman Страницы: 16

Бренд: Warm Tech Страницы: 24

Бренд: Country Hearth Страницы: 40

Бренд: IHP Страницы: 8

Бренд: Bond Страницы: 16

Бренд: Bond Страницы: 36

Бренд: Bond Страницы: 36

ECOFIRE MARTINA IDRO NEW 14

Бренд: Palazzetti Страницы: 12

Бренд: Enviro Страницы: 29

Бренд: White Mountain Hearth Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды