background image

8

   | 

Regency Horizon

®

 HZ33CE-11 Gas Fireplace

owner's information

IMPORTANT MESSAGE  
SAVE THESE 
INSTRUCTIONS

The  HZ33CE™  Fireplace  must  be  installed  in 
accordance with these instructions. Carefully read 
all the instructions in this manual first. Consult the 
"authority having jurisdiction" to determine the need 
for a permit prior to starting the installation. It is the 
responsibility of the installer to ensure this fireplace 
is  installed  in  compliance  with  manufacturers 
instructions and all applicable codes.

BEFORE YOU  START

Safe  installation  and  operation  of  this  appliance 
requires common sense, however, we are required 
by  the  Canadian  Safety  Standards  and  ANSI 
Standards to make you aware of the following:

GENERAL SAFETY  
INFORMATION

1.  The appliance installation must conform with 

local codes or, in the absence of local codes, 
with  the  current  Canadian  or  National  Gas 
Codes, CAN1-B149 or ANSI Z223.1 Installation 
Codes.

2.  The appliance when installed, must be electri-

cally grounded in accordance with local codes, 
or in the absence of local codes with the current 
National Electrical Code, ANSI/NFPA 70 or CSA 
C22.1 Canadian Electrical Code.

CHILDREN AND ADULTS SHOULD BE 
ALERTED TO THE HAZARDS OF HIGH 
SURFACE TEMPERATURES,  ESPE-
CIALLY THE FIREPLACE GLASS, AND 
SHOULD STAY AWAY TO AVOID BURNS 
OR CLOTHING IGNITION.  

INSTALLATION AND REPAIR SHOULD 
BE DONE BY AN AUTHORIZED 
SERVICE PERSON. THE APPLIANCE 
SHOULD BE INSPECTED BEFORE 
USE AND AT LEAST ANNUALLY BY A 
PROFESSIONAL SERVICE PERSON. 
MORE FREQUENT CLEANING MAY 
BE REQUIRED DUE TO EXCESSIVE 
LINT FROM CARPETING, BEDDING 
MATERIAL, ETC. IT IS IMPERATIVE THAT 
CONTROL COMPARTMENTS, BURNERS 
AND CIRCULATING AIR PASSAGEWAYS 
OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE 
APPLIANCE SHOULD BE LOCATED 
OUT OF TRAFFIC AND AWAY FROM 
FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS 
APPLIANCE CORRECTLY WILL VOID 
YOUR WARRANTY AND MAY CAUSE A 
SERIOUS HOUSE FIRE.

3.  See  general  construction  and  assembly  in-

structions. The appliance and vent should be 
enclosed.

4.  This appliance must be connected to the speci-

fied vent and termination cap to the outside of 
the  building  envelope.  Never  vent  to  another 
room or inside a building. Make sure that the 
vent is fitted as per Venting instructions.

5.  Inspect the venting system annually for blockage 

and any signs of deterioration.   

6.  Venting terminals shall not be recessed into a 

wall or siding.

7.  Any safety glass removed for servicing must be 

replaced prior to operating the appliance.

8.  To prevent injury, do not allow anyone who is 

unfamiliar with the operation to use the fireplace.

9.  Wear gloves and safety glasses for protection 

while doing required maintenance.

10. Be aware of electrical wiring locations in walls 

and ceilings when cutting holes for termination.

11. Under no circumstances should this appliance 

be modified. Parts that have to be removed for 
servicing should be replaced prior to operating 
this appliance.

12. Installation  and  any  repairs  to  this  appliance 

should be done by an authorized service per-

son. A professional service person should be 

called to inspect this appliance annually. Make 

it a practice to have all of your gas appliances 

checked annually.

13. Do not slam shut or strike the glass door.

14. Under no circumstances should any solid fuels 

(wood, paper, cardboard, coal, etc.) be used in 

this appliance.

15. The  appliance  area  must  be  kept  clear  and 

free of combustible materials, (gases and other 

flammable vapours and liquids.

CLOTHING OR OTHER FLAMMABLE 
MATERIAL SHOULD NOT BE PLACED 
ON OR NEAR THE APPLIANCE.

   

YOUNG CHILDREN SHOULD BE CARE-
FULLY  SUPERVISED WHEN THEY ARE 
IN THE SAME AREA AS THE APPLI-
ANCE.  TODDLERS, YOUNG CHILDREN 
AND OTHERS MAY BE SUSCEPTIBLE 
TO ACCIDENTAL CONTACT BURNS.  A 
PHYSICAL BARRIERS IS RECOMMEND-
ED IF THERE ARE AT RISK INDIVIDUAL 
IN THE HOUSE.  TO RESTRICT ACCESS 
TO A FIREPLACE OR STOVE, INSTALL 
AN ADJUSTABLE SAFETY GATE TO 
KEEP TODDLERS, YOUNG  CHILDREN 
AND OTHER AT RISK INDIVIDUALS OUT 
OF THE ROOM AND AWAY FROM HOT 
SURFACES. 

A BARRIER DESIGNED TO REDUCE 
THE RISK OF BURNS FROM THE HOT 
VIEWING GLASS IS PROVIDED WITH 
THIS APPLIANCE AND SHALL BE 
INSTALLED FOR THE PROTECTION 
OF CHILDREN AND OTHER AT-RISK 
INDIVIDUALS 

IF THE BARRIER BECOMES DAMAGED, 
THE BARRIER SHALL BE REPLACED 
WITH THE MANUFACTURER'S BARRIER 
FOR THIS APPLIANCE.

ANY SAFETY SCREEN, GUARD, OR 
BARRIER REMOVED FOR SERVICING 
AN APPLIANCE  MUST BE REPLACED 
PRIOR TO OPERATING THE APPLIANCE.

Содержание HORIZON HZ33CE





































































Отзывы: