Regency Fireplace Products Excalibur P90EX Скачать руководство пользователя страница 50

Страница: 50 / 72

Regency Excalibur

P90EX Direct Vent Gas Stove

installation

Remote Control Wall Mount

Holder/Cradle

The remote control/transmitter is supplied with a

remote-control wall mount holder, 2 screws/plugs.

See diagram 1.

Install the Remote-control wall mount holder ap

proximately 59” (1.5m) above the floor level, well

away from heat sources, kitchens, doors or windows.

Metallic structures or radio interferences can reduce

the operative distance of the device.

Make sure to attach the holder in a level plane

without any distortion.
Proceed as follow:

- Position the holder on the wall, using a level, mark

the points for the holes.

-Use a stud finder to determine if plugs are required

to drill into the wall and secure plugs to wall

- Fix the wall mount holder on the wall using the

screws supplied

- Insert the remote control onto the remote-control

holder.

Remote Control

Transmitter

Wall Mount

Holder/Cradle

2 Screws/

Plugs

Diagram 1

Содержание Excalibur P90EX









































































Результаты поиска

Содержание Excalibur P90EX

Отзывы:

Похожие инструкции для Excalibur P90EX

Бренды по названию

Популярные бренды

Regency Fireplace Products Excalibur P90EX, Инструкция для владельца и по установке

Результаты поиска

Содержание Excalibur P90EX

Отзывы:

Похожие инструкции для Excalibur P90EX

Бренды по названию

Популярные бренды