Regency Fireplace Products Excalibur P90EX Скачать руководство пользователя страница 51

Страница: 51 / 72

Regency Excalibur

P90EX Direct Vent Gas Stove | 51

installation

Wiring Diagram with Optional Wall Thermostat

If any of the original wires as supplied with the appliance must be replaced, it must be replaced with CSA type SEW (200

C) or its equivalent.

This heater does not require a 120V A.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/thermostat will

continue to operate as long as there are 4 AA batteries installed. However, a 120V A.C. power supply is needed for the fan/blower/lights operation.

Caution: Ensure that the wires do not touch any hot surfaces and are away from sharp edges.

This heater does not require a 120V A.C. supply for

operation. In case of a power failure, the remote

control/thermostat will continue to operate as long

as there are 4 AA batteries installed.

CAUTION:

Ensure that the wires do

not touch a hot surface and are away

from sharp edges.

WARNING:

Electrical Grounding

Instructions

This appliance is equipped with a

three pronged (grounding) plug

for your protection against shock

hazard and should be plugged

directly into a properly grounded

three-prong receptacle. Do not

cut or remove the grounding

prong from this plug.

Note:

4 AA Batteries must be installed into the back

up battery compartment however for this unit to

operate when power is lost. See battery back up

instructions in this manual The fan and or lights

will not operate during a power outage.

MODULE

911-373

REMOTE

OVERRIDE

WALL SWITCH

910-363

RECEPTACLE

BOX

WIRE

911-400

WIRE

911-401-ASM

911-398

SPARK

MH3V

VALVE

911-380 NG

911-381 LP

TX580 REMOTE

911-387

BATTERY

PACK

911-395

3 METER

WIRE HARNESS

FAN

911-389-ASM

P90EX WIRING DIAGRAM

6.40 x 3.95”

DC 6V

ADAPTER

911-394

POWER

LINE IN

FUSE

1A / 250V

5x20 mm

RED

ORANGE

BLACK

GREEN

BLACK

BROWN

WHITE

RED

BLACK

AUX300

911-365

PILOT

911-396-ASM NG

911-397-ASM LP

FLAME DETECT

GROUND

AA
AA
AA
AA

FAN

910-331/P

BLACK

911-399-ASM

911-037

GROUND

BLACK

WHITE

OPTIONAL

THERMOSTAT

A wall thermostat may be installed if

desired. Connect the wires as per the wiring

diagrams.

Note: Preferable if the thermostat is

installed on an interior wall.

Regency® offers an optional programmable

thermostat but any 250-750 millivolt rated non

anticipator type thermostat that is CSA, ULC or UL

approved may be used.

CAUTION

Do not connect the millivolt wall

thermostat wires to the 120V

wires

Содержание Excalibur P90EX









































































Результаты поиска

Содержание Excalibur P90EX

Отзывы:

Похожие инструкции для Excalibur P90EX

Бренды по названию

Популярные бренды

Regency Fireplace Products Excalibur P90EX, Инструкция для владельца и по установке

Результаты поиска

Содержание Excalibur P90EX

Отзывы:

Похожие инструкции для Excalibur P90EX

Бренды по названию

Популярные бренды