Regency Fireplace Products Excalibur P90EX Скачать руководство пользователя страница 33

Страница: 33 / 72

Regency Excalibur

P90EX Direct Vent Gas Stove | 33

installation

• Vent must be supported at offsets.

• Firestops are required at each floor level and whenever

passing through a wall.

• Maintain clearances to combustibles.

Note: Must use optional rigid pipe adaptor when using

rigid vent systems (Part # 510-994).

Rigid/Flex Pipe Venting Arrangements -

Vertical Terminations

The shaded area in the diagram shows all allowable combinations of

straight vertical and offset to vertical terminations, using two 90

elbow,

with

rigid pipe

vent systems for Propane and Natural Gas.

The P90EX is approved for a maximum 40 ft. straight vertical, with

rigid

pipe

4" x 6-5/8" vent systems for Propane and Natural Gas, as per diagram.

The shaded area in the diagram show all allowable combinations of

straight vertical and offset to vertical terminations with

rigid pipe

vent

systems for Propane and Natural Gas.

Maximum two 45

elbows allowed.

• Vent must be supported at offsets

• Firestops are required at each floor level and whenever

passing through a wall.

• Maintain clearances to combustibles as listed in the

"Clearances" section.

Please note that all vertical

measurements are taken

from the base of the unit

excluding

risers or bottom

standoffs.

Содержание Excalibur P90EX









































































Результаты поиска

Содержание Excalibur P90EX

Отзывы:

Похожие инструкции для Excalibur P90EX

Бренды по названию

Популярные бренды

Regency Fireplace Products Excalibur P90EX, Инструкция для владельца и по установке

Результаты поиска

Содержание Excalibur P90EX

Отзывы:

Похожие инструкции для Excalibur P90EX

Бренды по названию

Популярные бренды