Reely Sky QuadCopter 650 ARF Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 52

background image

28





12. LED Displays

The following LED display options are not safety indicators, but only indicate particular operating statuses. You will find
the LEDs for the displays described in the following on the control board (see figure 8).

a) Ready to Fly

After you have plugged in the flight battery and before starting the motors, the green LED lights up and the red LED is
off. Your QuadroCopter is ready to operate. If this is not the case, there is an interference. Please observe the following
operating instructions in this chapter.

b) Starting the QuadroCopter

Rev the motors. The red LED now lights up permanently and the green LED flashes. After approx. two seconds, the
green LED also lights up permanently. If this is not the case, there is an interference. Please observe the following
operating instructions in this chapter.

c) Configuration Mode

During the configuration of the remote control, the red LED indicates the programme step and the green LED indicates
the channel to be programmed through corresponding flashing with pauses.

d) RC Offset Adjustment

After the flight battery is connected, the red and green LEDs flash quickly and indicate the alignment of the transmitter
and electronic system of the QuadroCopter . After successful alignment has taken place, the red LED goes off and the
green LED is permanently lit.

e) Adjustment of the Neutral Position

If an adjustment to the neutral position is carried out, the green LED flashes quickly. The red LED is off.

The following LED display options are safety indicators. The causes for this must be explored and resolved.

f) Impaired Radio Link before Take-Off

You want to take off and the engines are still off. The red and the green LEDs flash slowly at the same time and
indicate a faulty radio link.

Possible causes:

Receiver crystal has fallen out of the base, receiver crystal is defective, receiver aerial has broken

off. Transmitter aerial not pulled out, second transmitter with the same transmitter channel switched on/ batteries from
transmitter empty. Check the possible causes and restart.

If there is any permanent radio interference during flight, the QuadroCopter will start an emergency landing and the
LEDs will also indicate an impaired radio link here by simultaneous flashing.

«
...
26
27
28
29
30
...
»

Содержание QuadCopter 650 ARF





















































Отзывы:

Нет отзывов

Похожие инструкции для QuadCopter 650 ARF

Бренд: QIMMIQ Страницы: 92

Бренд: Heli-Max Страницы: 20

Control FROXXIC

Бренд: REVELL Страницы: 14

Бренд: PowerVision Страницы: 87

Бренд: REVELL Страницы: 28

Бренд: SKY-HERO Страницы: 19

Бренд: XK Страницы: 8

Бренд: 4DRC Страницы: 9

Бренд: 4DRC Страницы: 16

Бренд: Saturn Multirotors Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды