Reely Sky QuadCopter 650 ARF Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 52

background image

26

If you do not set the neutral position , the QuadroCopter will use either the factory settings or the last saved value!

It is very important that you set the neutral position of the QuadroCopter as precisely as possible. For this,
it is necessary to set the neutral position on a completely horizontal base. Ideally, this should be measured
with a spirit level.

Due to different environmental conditions than in the factory and/or at the actual place of flight operation, the factory
settings may not be ideal! It is therefore urgently recommended that you set the neutral position before first flight.

If the QuadroCopter still swerves in one direction despite the relevant trims to the transmitter, the neutral position must
be stored again by slightly lifting up the QuadroCopter on the side to which it swerves. This way, the (changed) position
is saved as the new centre position.

«
...
24
25
26
27
28
...
»

Содержание QuadCopter 650 ARF





















































Отзывы:

Нет отзывов

Похожие инструкции для QuadCopter 650 ARF

Бренд: Jamara Страницы: 4

Бренд: dji Страницы: 18

Бренд: Hubsan Страницы: 28

Бренд: Blade Страницы: 2

Бренд: Blade Страницы: 6

Бренд: Blade Страницы: 15

Бренд: Blade Страницы: 16

Бренд: Blade Страницы: 26

Бренд: Skycat Страницы: 25

Бренд: 4DRC Страницы: 16

Бренд: Walkera Страницы: 21

Бренд: VISUO Страницы: 8

Бренд: SKY-WATCH7 Страницы: 72

Бренд: SWAGTRON Страницы: 16

RC Video One 370503003

Бренд: Carrera Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды