background image

red 

PRACTIKA 28-33 

USE AND INSTALLATION MANUAL  

Chapter 

12 

page 61 

 

Cleaning and maintenance 

 

        Technical dept. - All rights reserved - Reproduction prohibited 

 

change  the  operating  parameters  of  the  boiler  control  module  in  order  to  operate  the  appliance  with 
different modes and heat outputs, depending on the local heating requirements: 

 

Filling the fuel hopper 

– the fuel is poured into the system hopper. The pellet auger draws the 

fuel from the hopper and carries it to the main module of the pellet burner. 

 

Ash removal procedure 

– it is advisable to stop the pellet burner regularly (at least once every 

72  hours  of  operation  of  the  system),  wait  until  the  system  has  cooled  down  (at  least  30 

minutes)  and wipe away any ash residue in the heat exchanger  of the  hot  water  pellet boiler, 
scraping  it  away  manually  and  wiping  off  the  ash.  Remove  the  ash  residue  collected  in  the 

purpose-provided  ash  tray  of  the  boiler  if  necessary.  If  you  observe  this  procedure,  you  will 
ensure efficient heat exchange and retain the optimal operating conditions of your boiler. 

 

 

CAUTION

:  

regular removal of any ash residue deposited on the heat exchange surfaces of the boiler 
ensures  prolonged  and  reliable  operation,  as  well  as  efficient  and  economical 

performance of the appliance. 

 

 

Procedure  for  removing  ash  from  the  pellet  burner  grille

  –  after  the  system  has  been 

switched  off  and  the  burner  has  cooled  down  to  ambient  temperature,  open  the  boiler 
combustion  chamber  flap,  remove  the  burner  grille,  wipe  off  any  ash  residue,  reposition  the 
burner grille and then close the flap.

 

 

 

 

 

Содержание practika 28-33

































































Отзывы: