RED ORCHIDEA HYDRO Скачать руководство пользователя страница 50

Страница: 50 / 56

red

PELLET STOVES

Chapter 5

INSTALLATION AND USE MANUAL

page

Maintenance and cleaning

Technical service - Rights reserved - Reproduction prohibited

ATTENTION:
The frequency with which the smoke discharge

system is cleaned should be determined based on the

type of use that is made of the stove and the type of

installation.
We recommend relying on an authorized service

centre for end-of-season cleaning and maintenance,

they will carry out all of the previously mentioned

work and make a general check of the stove's

components.

5.2.1.

Shutting the stove down (end of season)

At the end of season, before shutting down the stove, we recommend

completely removing pellets from the hopper with the use of a vacuum

cleaner with an extension.

During periods of disuse, the stove must be unplugged and

placed in a dry place protected from the elements. For greater

safety, especially if there are children around, we recommend

removing the supply cable from the rear of the stove.

Upon re-start, when pressing the main switch (located on the back of

the stove) does not make the control panel display light up, it could

mean that the service fuse needs replacing.
On the rear of the stove there is a fuse holding compartment which is

located underneath the supply socket. Use a screwdriver to open the

fuse-holder compartment and if necessary replace them (3.15 AT

delayed)

5.2.2.

Check of internal components

ATTENTION!
The check of the internal electro-mechanical

components must be carried out only by qualified

personnel with technical knowledge of electricity and

combustion.

We recommend that an annual maintenance service is carried out,

preferably under a programmed service contract. The essential part of

this service is a visual and functional check on the following

components:



Reduction motor



Smoke expulsion fan



Smoke sensor



Heat-exchanger fan



Ignition sparkplug



Automatic resettable pellet/water thermostat



Room/water probe



Motherboard / service card



Fuses protecting panel - motherboard - services card



Wiring

Содержание ORCHIDEA HYDRO

























































Результаты поиска

Содержание ORCHIDEA HYDRO

Отзывы:

Похожие инструкции для ORCHIDEA HYDRO

Бренды по названию

Популярные бренды

RED ORCHIDEA HYDRO, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание ORCHIDEA HYDRO

Отзывы:

Похожие инструкции для ORCHIDEA HYDRO

Бренды по названию

Популярные бренды