background image

16 

 

 

 

A- CH circuit 

10- CH pump operating conditions. 
11- Operating conditions – opening mixing 
valve 
12-  Operating  conditions  –  closing  mixing 
conditions 
13- Signaling of the attached mixing valve 
14- Mixer turned off 
15-  Measured  temperature  on  the  CH 
sensor 
16- The controller is in the LATO mode (CH 
circuit turned off)  
17- Shorted thermostat signaling* 
(for circuits number 2 and 3) 
18-  Heating  state  signaling  on  the  CH 
circuit 
19-  Temperature  decrease  state  signaling 
on the CH circuit (for circuits number 1 and 
4) 

 

 

B- HW circuit 

20-  HW  circulating  pump  operating 
conditions 
21-  HW  tank  loading  pump  operating 
conditions 
22- Circulating pump turned off 
23-  HW  circuit  turned  off  (CH  sensor  not 
connected) 
24- Measured hot water temperature 
 

 

 

C- Info window 

25- Measured external temperature 
(displayed for CH circuit type no. 3 and 4) 
26- Day of the week display  
(i.e.: 1-Monday, 7 - Sunday) 
27- Clock 
28- Measured room temperature 
(displayed for CH circuit type no. 4) 
 

 

 

D- Boiler operation type 

29- Turning on boiler 
30- Turning off boiler 
31- Burning condition 
32- Feeding condition 
33- Stop – fan and feeder turned off 

 

 

E- Emergency pump configuration 

34-  Buffer  charging  pump  operating 
conditions 
35- BYPASS pump operating conditions 
(for an inactive emergency pump the place 
is empty) 

Содержание MultiFun







































Отзывы: