background image

27 

 

Heating temperature decrease 

Heating temperature decrease is a parameter that is set according to a selected "circuit control" option (set by 
the Service). 
 
 

For  manual  control,  the  temperature  decrease  of  the  heating  system  is  set  in  %.  The  temperature 

decrease is set in the 

CH Program

 option (see description below). 

   
 

For  installations  equipped  with  a  room  thermostat  (no  weather  sensor),  the  measuring  input  short-

circuit of the room sensor is a signal to the controller to lower the heating temperature by a set % value. For 
installations with a mixing valve, the valve will be closed and the temperature of the boiler will be decreased. 
 
 

For installations with an external sensor (the "circuit control" option needs to be set by the Service), the 

decrease is set in °C. The set value should apply to room temperature reduction. The controller will convert it to 
a  heating  temperature  decrease  value  taking  into  account  the  current  external  temperature  and  the  set 
weather characteristics. 
 
NOTE: 
1. PELLET fuel set. 
If  the  boiler  temperature  decrease  is  high,  the  regulator  can  stop  the  boiler.  For  a  several-degree  decrease 
(especially  for  the  PID  option  enabled  -  see:  Advanced/boiler/PID),  the  regulator  will  reduce  power  output 
without stopping it. 
2. WOOD fuel set. 
The  boiler  temperature  will  not  be  reduced  below  the 

minimum  boiler  temperature

  allowed  by  the 

manufacturer that is set in service parameters. Due to the risk of corrosion (a phenomenon of dew presence in 
the  burning  chamber),  the  controller  maintains  a  minimum  temperature  in  the  boiler  (see  the  minimum 
temperature parameter). 

SUMMER/WINTER/AUTO

2

modes 

This  parameter  is  used  to  manually  switch  the  regulator  into  the  SUMMER  or  WINTER  mode.  Moreover,  the 
AUTO mode can be chosen - the controller will automatically switch into the WINTER or SUMMER mode based 
on the outside temperature. 
 
In the summer mode only Hot Water is operated. In the WINTER mode, the controller controls the entire heating 
(CH + HW). 

Weather characteristics

3

 

If  the  Service  sets  an  option  that  uses  the  external  sensor,  the  menu  will  display  a  possibility  to  set  weather 
characteristics.  The  regulator  has  13  ready-made  characteristics  to  choose  from.  They  were  prepared  for 
buildings with different thermal isolation and different heating systems. When choosing the right option for a 
specific building, attention should be firstly paid to the heating type. For underfloor heating, characteristics in 
the range of 1-4 should be chosen, for radiator heating, 4-13. Then, insulation quality should be assessed. The 
worse  the  thermal  insulation  of  the  building,  the  higher  the  number  of  characteristics  should  be.  The  best 
solution is to select the average value. For underfloor heating it is good to set number 3, for radiator heating  - 
number 7. 
 
The full range of characteristics offered by MULTIFUN is presented further. 

                                                                 

2

 The AUTO operation mode is possible only for configurations with the external sensor. For simple options, the 

AUTO mode is not displayed. See „circuit control”. 

3

 The parameter is visible only after setting the operation configuration with the external sensor in the „Circuit 

control” (two configurations are available) 

Содержание MultiFun







































Отзывы: