background image

23 

 

ECO mode 

The ECO mode is recommended during summer. In this option, the burner is turned off when the boiler is heated 
up and the boiler temperature can decrease to any value (the anti-freeze function is still active). For the ECO 
mode turned off, the regulator always tries to maintain  a minimum temperature in  the boiler. Therefore, the 
burner may be turned on only to heat up the boiler, although in a given moment, none of the circuits will need 
heating up (for example, the dispenser is heated up and the CH circuit does not need heat - night decrease). 

Burner 

Turning on 

Fan operation prior to starting the turn-on process. The blowthrough aims at cleaning the furnace chamber of 
any flammable gas to safely turn on the boiler. 

 The time for which the feeder is to be turned on when feeding the first portion of fuel.  

Heater operation time prior to turning on the fan.  

Note:  depending  on  the  heater  model,  set  the  time  specified  by  the  manufacturer.  For  some  models,  it  is 
required to set 0 sec., because the heater operation without cooling it with air may damage it. 

Fan  output  during  boiler  turn-on.  This  parameter  should  be  set  depending  on  the  type  of  fuel  and  chimney 
draught. 

A too long operation time may damage the heater. Set the heater operation time according to documentation. 
After the maximum heater operation time passes, the regulator will turns off the heater and go to the next step 
of  the  turn-on  procedure.  The  heater  will  be  turned  off  earlier  when  the  light  sensor  detects  a  flame  in  the 
burner. 

This parameter specifies the flame brightness in the burner the regulator of which acknowledges that pellet is 
burning.  During  the  turn-on  process,  the  heater  is  turned  off  and  the  full  turn-on  stage  takes  place.  During 
burning,  the  regulator  controls  the  flame  brightness.  When  it  remains  lower  than  the  set  threshold,  an 
emergency stop of the burning process is activated and the burner is turned off. 

 If, during the ignition procedure, the regulator does not detect a flame after the set time, the ignition process 
will start again. After the second failed attempt, the regulator will trigger an emergency stop of the burner. If 
the  ignition  process  goes  smoothly  and  the  fuel  is  ignited,  the  regulator  will  gradually  enhance  the  airflow 
during the whole full ignition time. Please note that the burner has only a starting portion of fuel and the time 

Blowthrough time 

Initial charge time 

Heater heat up time 

Fan output  

Maximum heater operation time  

Flame brightness  

Full ignition time 

Содержание MultiFun







































Отзывы: