background image

REC TwinPeak Series Installation Manual - UL 1703
Rev B - 03.15 

Ref: NE-06-08-B

5

panEl HanDlInG

To avoid damage to the solar cells and other components, all solar panels should be handled with care.  all warnings and instructions on the packaging 

should be observed.  Follow these guidelines when unpacking, transporting or storing the panels:

• 

Record the serial numbers prior to installation and note the information in the system documentation. 

• 

Carry the panels using both hands and avoid using the junction box as a grip.

• 

Do not allow the panels to sag or bow under their own weight when being carried. 

• 

Do not subject the panels to loads or stresses e.g., leaning or placing heavy objects on them. 

• 

Do not stand on the panels or cause impact through dropping them. 

• 

keep all electrical contacts clean and dry.

• 

Store panels in a  dry and properly ventilated room.

• 

Do not apply force to the backsheet.

• 

avoid using sharp or pointed objects if panels require marking.

• 

Never apply paints, adhesives or detergents to the back of the laminate.

• 

Do not use any solar panel that is damaged or been tampered with.

• 

Never attempt to disassemble the panels.

If the panel front glass is broken or laminate back sheet is damaged, it can expose personnel to hazardous voltages. 

MECHaNiCaL iNSTaLLaTioN 

fIRE GuIDElInEs

REC TwinPeak panels have a Class C, Type 2 Fire classification.  The fire rating of this panel is only valid when mounted in the manner specified in these 

mechanical mounting instructions.  Utilize the following fire safety guidelines when installing REC TwinPeak panels: 

• 

Check with local authorities for fire safety guidelines and requirements for any building or structure on to which the panels will be installed.

• 

The system design should ensure that it can be easily accessed in the event of a building fire.  

• 

Check with local authorities for applicable regulations concerning setbacks or other placement restrictions that may apply for roof-mounted 

arrays.

• 

The use of DC ground fault interrupters is recommended.  This may also be required by local and national codes.

• 

all electrical appliances are a fire risk.  The panel should therefore be mounted over a fire retardant roof covering rated for the application and 

a suitable distance of 4 in (100 mm) between the panel and the mounting surface, allowing free circulation of air beneath the panels, should be 

respected at all times.

oRIEntatIon

To maximize system output, panels should be installed at the optimum orientation and tilt angle.  The specifics of this depend on location and can be 

calculated by a qualified system designer.  a lower angle of panel installation increases the requirement for regular cleaning. 
The optimal mounting position of panels results in the sun’s rays falling perpendicular (i.e. at 90°) to the surface.  all panels in a string should, wherever 

possible, have the same orientation and tilt to ensure the system does not underperform due to mismatched outputs.

The panels must not be exposed to artificially concentrated sunlight.

EnVIRonmEntal faCtoRs

REC TwinPeak panels are designed to provide decades of durable and stable output.  ambient operating temperatures should be between -40 and 

185°F (-40 and +85°C). 
The panels are not suitable for installation in potentially hazardous locations nor should they be installed in the following locations: 

• 

Near sources of flammable gases or vapors

• 

Near open flames.

• 

Under water or in water features.

• 

where exposed to sulfur e.g. near sulfur springs or volcanoes.

• 

where the panels may be exposed to harmful chemicals.

Ensure panels are not exposed to direct contact with salt water/spray and avoid installation in areas subject to high salt mist content e.g. 

coastal areas.

Содержание REC265 Series













Отзывы: