1.
This fire table comes equipped with a standard LP gas hose and regulator including the
appliance side connection for a CGA No 791 Cylinder Connection Device. The LP gas hose and
ƫƫƫƫ.!#1(0+.ƫ/1,,(%! ƫ3%0$ƫ0$%/ƫü.!ƫ0(!ƫ)1/0ƫ!ƫ1/! ċƫ*(5ƫƫ$+/!ƫ* ƫ.!#1(0+.ƫ/,!%ü! ƫ5
manufacturer can be used for replacement.
a.
ƫ$!ƫƫ+ƫĈĊāƫ+**!0%+*ƫ%*+.,+.0!/ƫƫ)#*!0%ƫý+3ƫ(%)%0%*#ƫ !2%!ƫ0$0ƫ0/ƫƫ
ƫƫƫƫƫ0+ƫ(%)%0ƫ0$!ƫý+3ƫ+"ƫ#/ƫ%"ƫƫ(!'ƫ%/ƫ !0!0! ƫ!03!!*ƫ0$!ƫ.!#1(0+.ƫ* ƫ0$!ƫ1.*!.ƫ2(2!ċ
b.
If the burner valve is open prior to the LP gas cylinder service valve being opened,
ƫƫƫƫƫƫ0$!ƫ+**!0%+*ƫ3%((ƫ%*0!.,.!0ƫ0$%/ƫ".!!ƫý+3ƫ+"ƫ#/ƫ0+ƫ!ƫƫ(!'ċ
c.
ƫ$!ƫ+**!0%+*ƫ/"!05ƫ"!01.!ƫ3%((ƫ.! 1!ƫ#/ƫý+3ƫ".+)ƫ0$!ƫ.!#1(0+.ƫ0+ƫ0$!ƫƫ
appliance to a minimal level.
d.
Be sure that the burner control valve is closed prior to opening the LP gas cylinder
ƫƫƫƫƫ/!.2%!ƫ2(2!ƫ0+ƫ!*/1.!ƫ0$0ƫ0$!ƫ+**!0%+*ƫý+3ƫ(%)%0%*#ƫ !2%!ƫ%/ƫ*+0ƫ0.%##!.! ƫƫ
mistakenly.
e.
ƫ "ƫ0$!ƫ+**!0%+*ƫý+3ƫ(%)%0%*#ƫ !2%!ƫ%/ƫ0.%##!.! ƫ)%/0'!*(5Čƫ(+/!ƫ0$!ƫƫ#/ƫƫ
ƫƫ ƫƫ5(%* !.ƫ/!.2%!ƫ2(2!ƫ* ƫ0$!ƫ1.*!.ƫ2(2!Čƫ3%0ƫāĀƫ/!+* /ƫ0+ƫ((+3ƫ0$!ƫ !2%!ƫ0+ƫƫ
reset, open the cylinder service valve, then open the burner valve and light the
fireplace as per lighting instructions.
2.
Be sure to protect the hose from any hot surfaces. Serious danger may result if the hose
contacts any hot surface.
3.
!#1(.ƫ)%*0!**!ƫ+"ƫ0$!ƫ$+/!ƫ* ƫ.!#1(0+.č
a.
Inspect the hose before each use of the fire table. If the hose shows signs of
cracks, abrasions, cuts or damage of any kind, do not operate the appliance. Fix or
replace the hose as required before using the appliance. For assistance with repair
ƫ ƫƫƫƫ+.ƫ.!,(!)!*0ƫ+"ƫ0$!ƫ$+/!Čƫ((ƫ!(ƫ()!ƫ0ƫāġĉĀĀġćĆąġāĈĀąċƫ/!ƫ+*(5
replacement parts from the manufacturer.
b.
Inspect the seal inside the CGA No 791 service valve on the LP gas cylinder when
replacing the cylinder or at least once per year. If there is any indication of
damage, have the seal replaced by a certified gas dealer before operating the
appliance.
4.
Do not use tools to tighten the CGA No 791 connection nut onto the LP gas cylinder service
valve. Hand tighten only.
5.
Be careful to not cross the threads on the connection when tightening the CGA No 791
connection on to the LP gas cylinder service valve.
6.
ƫė!'ƫ!/0Ęƫ/$+1( ƫ(35/ƫ!ƫ,!."+.)! ƫ"0!.ƫ00$%*#ƫ0$!ƫ+**!0%+*ƫ0+ƫ0$!ƫƫ#/ƫ5(%* !.
ƫƫƫƫƫ/!.2%!ƫ2(2!ċƫĨ!!ƫė$!'%*#ƫ"+.ƫ!'/Ęƫ/!0%+*ƫ+"ƫ0$%/ƫ)*1(ƫ+*ƫ,#!ƫāĀĩ
7.
ƫ+.ƫ0$!ƫ+**!0%+*ƫ+"ƫ0$!ƫ$+/!ƫ* ƫ.!#1(0+.ƫ0+ƫ0$!ƫƫ0*'Čƫ.!"!.ƫ0+ƫ0$!ƫė+**!0%+*Ęƫ/!0%+*
of the LP gas cylinder section above.
Gas Component Connection Checks (Cont.)
17
ăċƫ
ke sure that the igniter pin and thermocouple are correctly positioned.
ġƫ
The igniter pin should be pointed straight to the thermocouple.
ġƫ
The thermocouple should be positioned 5mm away from the burner tube.
ąċƫ
ke sure that the thermocouple wire is correctly positioned. The
thermocouple wire should be in line with the valve.
Igniter Box
Thermocouple Wire
Thermocouple
Wire
Wire should
be in line
with valve
Valve
Valve
5mm
Thermocouple
Igniter Pin
Pilot Light
