ReadyLift 44-3060 Скачать руководство пользователя страница 24

Страница: 24 / 26

www.ReadyLIFT.com

Phone: (877) 759

9991

3060/44

3080IM

Install the provided U

bolts and nuts.

Snug up but do not tighten at this

time. Repeat for the opposite side.

When tightening, use a criss

cross

pattern. Alternate between sides of

the vehicle. Final torque will be com-

pleted when the vehicle is on the

ground.

Install your extended length shocks

to the frame and axle. use the

facto-

ry hardware

. Use manufactures in-

struction for proper installation.

Install the provided

brake line brack-

to the differential. Use factory

hardware. Attach the brake line to

the extended bracket. Use provided

hardware. Torque to

20 ft

lbs.

Lower the axle just enough to install

the ReadyLIFT lift block. Make sure

the tapered end of the block is fac-

ing forward, and the bump stop tag

is inboard. Raise the axle until the

block is seated in the locating pins.

Содержание 44-3060



























Результаты поиска

Содержание 44-3060

Отзывы:

Похожие инструкции для 44-3060

Бренды по названию

Популярные бренды

ReadyLift 44-3060, Руководство пользователя

Результаты поиска

Содержание 44-3060

Отзывы:

Похожие инструкции для 44-3060

Бренды по названию

Популярные бренды