Raytec VARIO2 IP 16 Series Скачать руководство пользователя

Страница: 61 / 64

Hard Reset Button

–

Located on illuminator

A hardware reset button feature has been provided that will restore ALL factory
default settings including

IP address

user names

and

passwords

etc. and can be

used in cases where communication is lost and the illuminator does not respond.

WARNING: We recommend attempting to reconnect with the

illuminator by firstly restarting the illuminator or restoring

factory settings via the integrated web interface. The hard reset

button on the illuminator should be used only as a last resort.

To reset all parameters and the IP address to Factory Default settings:

Disconnect power from the illuminator.

Remove the baseplate on the illuminator to access the reset button.

Press and hold the Reset button and reconnect power.

Keep the Reset button pressed for approximately 5 seconds until the
illuminator flashes. Release the Reset button.

Replace the baseplate securely to ensure unit remains waterproof.

The illuminator can now be discovered using the Raytec Discovery Tool and can be
configured as normal following the instructions in this manual. Be aware that the IP
address will have been restored to factory default, 192.168.2.80.

Hard Reset Button

Содержание VARIO2 IP 16 Series

































































Результаты поиска

Содержание VARIO2 IP 16 Series

Отзывы:

Похожие инструкции для VARIO2 IP 16 Series

Бренды по названию

Популярные бренды

Raytec VARIO2 IP 16 Series, Полное руководство по установке и настройке

Результаты поиска

Содержание VARIO2 IP 16 Series

Отзывы:

Похожие инструкции для VARIO2 IP 16 Series

Бренды по названию

Популярные бренды