RaySafe i3 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 39

RaySafe i3 Скачать руководство пользователя страница 30

30

RaySafe i3 Installation & service manual – Settings explained

PARAMETER

EXPLANATION

Connection test

Check the connectivity for the hub by pinging for example the Video Unit.

Install a https certificate

If you want to use a custom https certificate, you can install it on the hub.
The hub needs to reboot to start using the new certificate. Only https
certificates in pfx formats are supported.

Software update

If the hub needs a software update, you select a file for upload and follow
the instructions.

DATA EXPORT TAB

Figure 21. Real-time Hub Data export tab.

For the

CSV export

choices, see “Data export” on page 24.

When you log in with the System configuration account, you will also access the following exports below the header

Troubleshooting

.

BUTTON

EXPLANATION

Connect & Disconnect

A log of
•  dosimeter connect and disconnect events
•  hub reboots
•  hub time set events.

Hub status

An overview of the most important status parameters for the hub.

Hub status history

A change log for the most important configuration change events.

NOTE:

Selecting Local timezone for export will not be reflected in
this export, which always uses the time defined by the time
source (UTC if NTP is used).

«
...
28
29
30
31
32
...
»

Содержание i3








































Отзывы:

Нет отзывов