RaySafe i3 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 39

RaySafe i3 Скачать руководство пользователя страница 26

26

RaySafe i3 Installation & service manual – Settings explained

SETTINGS EXPLAINED

VIDEO UNIT

SIGN IN

Figure 15. Video Unit Sign in screen.

Sign in for the system configuration. The default password is

raysafe

.

SET-UP TAB

Figure 16. Video Unit Set-up tab.

PARAMETER

EXPLANATION

IP address

Enter the IP address for the Video Unit.

Subnet mask

Enter the address for the Subnet mask.

Default gateway

Enter the address for the Default gateway.

Hub IP address

Enter the IP address for the Real-time Hub connected to the system.

Password

Change the password for the Video Unit.

Video settings, Resolution
Video settings, Refresh rate (Hz)

Auto will use the resolution preferred by the monitor and is suitable in most
cases.

If there are problems with the automatic resolution, you can manually
select a resolution from the list. The options for

Resolution

and

Refresh

rate

are defined by the connected monitor.

Video settings, Scaling factor

In some cases, you need to scale the picture for proper fit.

«
...
24
25
26
27
28
...
»

Содержание i3








































Отзывы:

Нет отзывов