Raypak 88AR-398A, Инструкция по установке и эксплуатации

Страница: 42 / 68

42
Table Q: Adjust Menu
Item Application Range Description Default User
TARGET MODE 1, 2, 3 RSET <> SETP RSET = Outdoor Reset, SETP =Setpoint SETP
MODE MODE 1, 2, 3 1, 2, 3 Piping and application configuration. 1
SETPOINT MODE 1, 2, 3 50°F to 192°F
Boiler target temperature while a heat
demand is present for setpoint operation
180°F
OUT START MODE 1, 2, 3 35°F to 85°F Outdoor starting temperature - outdoor reset 70°F
OUT DESIGN MODE 1, 2, 3 -60°F to 45°F Outdoor design temperature - outdoor reset 10°F
Boil START MODE 1, 2, 3 35°F to 150°F
Starting boiler target temperature when the
outdoor temperature is at outdoor start out-
door reset
70°F
Boil DESIGN MODE 1, 2, 3 70°F to 200°F
Design boiler target temperature when the
outdoor temperature is at outdoor design
outdoor reset
180°F
TARGET MAX MODE 1, 2, 3 100°F to 192°F Maximum target system temperature 192°F
TARGET MIN MODE 1, 2, 3 OFF, 50°F to 190°F Minimum target system temperature 50°F
TARGET DIFF MODE 1, 2, 3 2°F to 42°F Differential for target system temperature 10°F
IND SENSOR MODE 1, 2, 3 OFF <> ON
Selects whether a DHW sensor is used for
indirect DHW tank
OFF
IND SETP MODE 2, 3 OFF, 50°F to 180°F
Target Indirect DHW Tempererature (IND
Sensor = ON, to enable this setting)
140F
DHW DIFF MODE 2, 3 2°F to 10°F
Differential for the target indirect DHW tank
temperature, Requires IND Sensor = ON
6°F
IND SUPPLY MODE 2, 3 OFF, 50°F to PIM value*
Target boiler temperature for the DHW heat
exchanger during indirect DHW operation,
requires IND Sensor = OFF
180°F
DHW
PRIORITY
MODE 2 OFF <> ON
Selects whether or not Indirect DHW priority
is active during indirect DHW operation
OFF
PRI OVR MODE 2, 3 Au, 0:10hr to 2:00hr
Sets the length of the indirect DHW priority
override time
1:00hr
SYS PURGE All OFF, 0:20min to 20:00min
Sets the length of the system pump post
purge
20
seconds
MIX TYPE All H (BOIL <> PLNT)
Selects the type of control depending on
pipe configuration for CWP
H BOIL
MIX TARGET All 50°F TO 140°F Inlet Target Temperature 120F
MIX LOCK All ON <>OFF
The equipment will trigger a warning when
“MIX Target” is not reached within 7 min-
utes. MIX LOCK = ON Alarm and lockout,
MIX LOCK = OFF Alarm only
OFF
MIX TRIM All -5 to 5
This adjustment is for various types and
sizes of units as well as various actuator
motor speeds and types supplied by Raypak
0
MIX SPEED All FAST <> MED <> SLOW This setting defines speed of response. MED
MIX INV All ON <>OFF
This option is related to the use of spring
return actuators with a proportional valve
OFF
WWSD MODE 1, 2, 3 40°F to 100°F
The system warm weather shutdown tem-
perature outdoor reset, requires TARGET =
REST
70°F
UNITS All deg F <> deg C Show units using icons in display deg F
MODBUS All OFF<>MNTR<>TEMP<>RATE
ModBus Operating Mode: Off, Monitor, Temp
Control, Rate Control
OFF
ADDRESS All 1 to 247 ModBus slave address 1
DATA TYPE All RTU <> ASCI Modbus data type RTU
BAUD RATE All 2400<>9600<>19K2<>57K6<>115K 19K2
PARITY All NONE<>EVEN<>ODD EVEN
* Fixed values based on the ID card.