Rayjet 8015 Скачать руководство пользователя страница 48

Страница: 48 / 53

No engraving or

cutting

Skipped cut lines or skipped

engraving

Set the right functions in the

parameter window (double
click on the plate)

Problems with

printing jobs to
the JobControl

Printer settings

Go to the TROTEC printer

properties (start/settings/fax
and printers).

Choose the “Port” tab and select

the right directory and “local
port”.

Choose the “Advanced” tab and

select “print directly to the
printer”

Click OK

Problems with

cutting lines in
Corel Draw

Color management

Disable the color management in

Corel Draw.

Please use the Corel help to find

the color management in your
Corel version

Printing fails

There was an
error found when
printing the
document
“xyz.cdr” to
TROTEC: Do you
want to retry or
cancel the job?

Incorrect spool path

Set valid spool path within

JobControl/Settings/Options/G
eneral/Spoolpath.

Jumbled bitmaps

when printing.

“Print directly to the printer” not

activated.

Go to the printer properties

(start/settings/fax and
printers).

Choose the “Advanced” tab and

select “print directly to the
printer”

Click OK

No colors are

displayed in
material dialog.

Material file (e.g.

TR_CO2_Material.dat) is write
protected (copy from CD-ROM)

Override write protection.

Error message

when attempting
to print. “Unable
to access printer
driver. Try
removing and
reinstalling this
printer driver.”

Previous job-size too small.

Reinstallation of the driver does not

resolve the problem!

Go to the TROTEC printer

properties (start/settings/fax
and printers).

Choose the “Print” tab and set

Width and Height to
something like 100mm (4 in)

Click OK

Содержание 8015






















































Результаты поиска

Содержание 8015

Отзывы:

Похожие инструкции для 8015

Бренды по названию

Популярные бренды

Rayjet 8015, Руководство по обслуживанию

Результаты поиска

Содержание 8015

Отзывы:

Похожие инструкции для 8015

Бренды по названию

Популярные бренды