Raycus RFL-QCW300 Скачать руководство пользователя страница 25

Страница: 25 / 50

Wuhan Raycus Fiber Laser Technologies Co., Ltd

User Guide RFL-QCW300/3000

Pulses are generated internally with parameters set by sending corresponding commands via

RS-232 or Ethernet. Start and stop of the pulse train is controlled by means of modulation signal

applied to the pins 17-9 of the DB-25 interface connector under the assumption that emission has

been enabled before.

The details of the main control functions in all modes and sub-modes of operation are listed

in Table 6.

Table 6 Main Control Functions

Emission Enabling

Hardware Emission Control Enabled

Hardware Emission Control Disabled

Control interface

(DB-25 – pin7-9)

RS-232 or Ethernet

Power Setting

Analog Power Control Enabled

Analog Power Control disabled

Control interface

(DB-25 – pin8-9)

RS-232 or Ethernet

Guide Laser

Enabling

External Aiming Beam Control Enabled

External Aiming Beam Control disabled

Control interface

(DB-25 – pin21-9)

RS-232 or Ethernet

Reset Errors

RS-232 or Ethernet or Analog Interface

Available Operation

Modes

CW, Pulsed

Available Operation

Sub-Modes

Standalone, Modulation, Gate

Operation Mode

Selection

RS-232 or Ethernet

1: To enable HARDWARE EMISSION CONTROL send the command ―ELE‖ via RS-232 or Ethernet interface, to disable -

―DLE.‖

2: To enable ANALOG POWER CONTROL send the command ―EEC‖ via RS-232or Ethernet interface, to disable - ―DEC.‖

3: To enable EXTERNAL AIMING BEAM CONTROL send the command ―EEABC‖ via RS-232 or Ethernet interface, to

disable - ―DEABC.‖

Wave mode

The Raycus software can reads a waveform file from the memory if a waveform has been

edited and stored before (See Appendix 1.6 ―Waveform Editing‖ for more information about

how to edit and store a waveform). The output power for the laser varies with the waveform

受

控

武汉锐科

Содержание RFL-QCW300



















































Результаты поиска

Содержание RFL-QCW300

Отзывы:

Похожие инструкции для RFL-QCW300

Бренды по названию

Популярные бренды

Raycus RFL-QCW300, Руководство пользователя

Результаты поиска

Содержание RFL-QCW300

Отзывы:

Похожие инструкции для RFL-QCW300

Бренды по названию

Популярные бренды