Wuhan Raycus Fiber Laser Technologies Co., Ltd
User Guide RFL-QCW300/3000
25
Table 9 ( continued )
Code
Description
Examples
RCT
Read Laser Temperature — Reads the internal temperature
of the laser. The response is an echo of the command, a
delimiter of ―:‖, and the temperature in degrees centigrade.
Sent
：
―RCT‖
Response
：
―RCT:34.5‖
RDGW
Read Default Gateway –Reads the current default gateway of
the device. The response is the command echoed back, followed
by a delimiter of ―:‖ and then the default gateway in dot-decimal
notation.
Sent
：
―RDGW‖
Response
：
―RDGW:192.168.0.1‖
RERR
Reset Errors — Resets any resettable errors.
Sent
：
―RERR‖
Response
：
―RERR‖
RIP
Read IP –Reads the current IP address of the device. The
response is the command echoed back, followed by a delimiter
of ―:‖, and then the IP address in dot-decimal notation.
Sent
：
―RIP‖
Response
：
―RIP
：
192.168.0.10―
RMASK
Read Subnet Mask — Reads the current subnet mask of the
device. The response is the command echoed back, followed by
a delimiter of ―:‖, and then the subnet mask in dot-decimal
notation.
Sent
：
―RMASK‖
Response
：
―RMASK
：
255.255.255.0‖
RPRR
Read Pulse Repetition Rate — Reads the pulse repetition rate.
The response is the command echoed back, followed by a
delimiter of ―:‖ and then the pulse width in Hz.
Sent
：
―RPRR‖
Response
：
―RPRR
：
10‖
(Indicates that the PRR is 10 Hz)
RPW
Read Pulse Width — Reads the pulse width. The response is the
command echoed back, followed by a delimiter of ―:‖ and then
the pulse width in milliseconds (ms).
Sent
：
―RPW‖
返回：
―RPW
：
5.5‖
(Indicates that the pulse width is
5.5 ms)
SDC
Set Diode Current — Sets the diode current. The units are in
percent of maximum current. The setpoint must be below 100%
and above the minimum current setpoint. The current can also
be set to 0. The response from the laser is the command echoed
back, a delimiter of ―:‖ and then the current setpoint for the
laser. A value that is outside the acceptable range receives a
response of ―ERR: Out of Range.‖
Sent
：
―SDC 34.2‖
Response
：
―SDC
：
34.2‖
(Current Setpoint is set to34.2%)
Sent
：
―SDC 104.2‖
Response
：
―ERR
：
Out of Range‖
(The setpoint is unchanged)
SDGW
Set Default Gateway —Followed by a number in dot-decimal
notation sets the default gateway for the laser.
Sent
：
―SDGW 192.168.0.1‖
Response
：
―SDGW: 192.168.0.1‖
SIP
Set IP — Followed by a number in dot-decimal notation sets the
IP address for the laser.
Sent
：
―SIP 192.168.0.10‖
Response
：
―SIP 192.168.0.10‖
SMASK
Set Subnet Mask— Followed by a number in dot-decimal
notation sets the subnet mask for the laser.
Sent
：
―SMASK 255.255.255.0‖
Response
：
―SMASK
255.255.255.0‖
受
控
武汉锐科
