Raycus RFL-QCW300 Скачать руководство пользователя страница 42

Страница: 42 / 50

Wuhan Raycus Fiber Laser Technologies Co., Ltd

User Guide RFL-QCW300/3000

Figure 10 Control Mode Setting

Note

：

Steps of laser emission start:

Step 1: Enable emission control

(Enable emission control is performed by signal applied to the pins 7-9 of the DB-25

interface connector if hardware emission control is enabled (ELE), while it is performed by

command via RS-232 or Ethernet if hardware emission control is disabled (DLE).)

Step 2: Starts/Stops emission

(In Standalone mode, emission starts is performed by command via RS-232 or Ethernet; In

Gate/ Modulation /Wave mode, emission is performed by signal applied to the pins 17-9 of the

DB-25 interface connector)

Click

―

DEABC

‖indicate that the aiming beam

ON/OFF is controlled by buttons of ―ABF/ABN‖;

Click

―

EEABC

‖indicate that the aiming beam

ON/OFF is controlled by signal applied to the pins

7-9 of the DB-25 interface connector.

Click

―

Pulse

‖ indicate that the laser is operating in

PULSE mode; Click

―

‖ indicate that the laser is

operating in CW mode.

Click

―

EGM

‖ indicate that internal pulse generator is

enabled and laser pulse sequence is performed by signal

applied to the pins 7-9 of the DB-25 interface connector.

Click

―

EMOD

‖ indicate that the internal pulse

generator is disabled and Emission start/stop is

performed by signal applied to the pins 17-9 of the

DB-25 interface connector.

Click

―

ELE

‖ indicate that hardware emission control is

enabled and Emission start/stop is performed by signal

applied to the pins 7-9 of the DB-25 interface

connector.

Click

―

EWPM

‖ indicate that laser is operating in Wave

mode.

Pulse

Click

―

EEC

‖ indicate external power control is enabled

and power level is set via external analog voltage applied

to the pins 8-9 of the DB-25 interface connector.

Click

―

DEC

‖ indicate external power control is disabled

and power level is set via (RS-232 or Ethernet).

受

控

武汉锐科

Содержание RFL-QCW300



















































Результаты поиска

Содержание RFL-QCW300

Отзывы:

Похожие инструкции для RFL-QCW300

Бренды по названию

Популярные бренды

Raycus RFL-QCW300, Руководство пользователя

Результаты поиска

Содержание RFL-QCW300

Отзывы:

Похожие инструкции для RFL-QCW300

Бренды по названию

Популярные бренды