Raycus RFL-C1000 Скачать руководство пользователя страница 44

Страница: 44 / 44

Wuhan Raycus Fiber Laser Technologies Co., Ltd

ser Guide of 1000W CW laser

Raycus User Guide | Warranty, Return and Maintenance



WARNING

: It is the customer’s responsibility to understand and

follow operating instructions in this User Guide and specifications prior to

operation-failure to do so may void this warranty. Accessories and fiber

connectors are not covered by this warranty.

6.3 Service and Repair



Do not open the device. There are no user serviceable parts, equipment or
assemblies for user in this product. All service and maintenance shall be
performed by qualified Raycus personnel.



Please contact Raycus as soon as possible when problems under warranty about
maintenance happened to the product.



The product returned with permission should be placed in a suitable container.



If any damage happened to the product, please notify the carrier in document
immediately.

We reserve the right to make changes in design or constructions of any of

our products at any time without incurring any obligation to make changes or
install the same on units previously purchased.

All the items about warranty and service above provided by Raycus are

for uses’ reference; formal contents about warranty and service are subject to
the contract.

Содержание RFL-C1000













































Результаты поиска

Содержание RFL-C1000

Отзывы:

Похожие инструкции для RFL-C1000

Бренды по названию

Популярные бренды

Raycus RFL-C1000, Руководство пользователя

Результаты поиска

Содержание RFL-C1000

Отзывы:

Похожие инструкции для RFL-C1000

Бренды по названию

Популярные бренды