Raycus RFL-C1000 Скачать руководство пользователя страница 6

Страница: 6 / 44

Wuhan Raycus Fiber Laser Technologies Co., Ltd

ser Guide of 1000W CW laser

Raycus User Guide | Safety Information

1: Laser Output Head

2: Type 4 Laser

Product

3: Class 2M Laser Product

Label-1mW Red Laser

4: CE Authentication

5: ID Label

6: Laser Radiation

Hazard

7: Electrical

Hazard

1.4 Optical Safety

Any dust on the end of the collimator assembly can burn the lens.



CAUTION:

DO NOT emit laser when the protective

cap is not removed, otherwise the lens or crystal will be

damaged.

1.5 Electrical Safety

1) Make sure the product is firmly grounded through the PE line of the AC

power cord.



WARNING:

Any interruption from the protective earth

will electrify the enclosure, which may result in personal

injury for operators.

2) Make sure that the correct voltage of the DC power source is used.

Содержание RFL-C1000













































Результаты поиска

Содержание RFL-C1000

Отзывы:

Похожие инструкции для RFL-C1000

Бренды по названию

Популярные бренды

Raycus RFL-C1000, Руководство пользователя

Результаты поиска

Содержание RFL-C1000

Отзывы:

Похожие инструкции для RFL-C1000

Бренды по названию

Популярные бренды