Raveon FireLine Ethernet Скачать руководство пользователя | Manualshive

Страница: 3 / 34

background image

Congratulations!

Congratulations on your purchase of a FireLine radio modem.

Please take a few minutes to read this manual carefully. The information
presented here will allow you to derive maximum performance from your radio
modem. After reading it, keep the manual handy for quick reference, in case
questions arise later on.

NOTICE

There are no user-serviceable points inside this transceiver. All service jobs
must be referred to your Authorized Service Center or Raveon Technologies
Service Department.

Safety / Warning Information

WARNING

- DO NOT operate theRV-M5-U radio modem when bystanders

are within 2 feet (.6 meters) of the antenna.

Safety Training information:

Antennas used for this transmitter must not exceed an antenna gain of 0 dBd.
The radio modem must be used in fixed vehicle-mount configurations or at
fixed base-station sites. It is not intended for portable applications.

Failure to observe these restrictions may result in exceeding the FCC RF
exposure limits.

Antenna Installation:

For rear deck trunk installation, the antenna must be located at least the
following range away from rear seat passengers and bystanders in order to
comply with the FCC RF exposure requirements.

For roof top installation, the antenna must be placed in the center of the roof.

Radiated frequency and Distance

RV-M5-UC

1.97 Feet (0.6 m)

FCC ID: SRS-RV-M5-UC

Raveon Technologies Corporation

«
1
2
3
4
5
...
»

Содержание FireLine Ethernet



































Отзывы:

Нет отзывов

Похожие инструкции для FireLine Ethernet

Бренд: C-motech Страницы: 11

Бренд: Easlink Страницы: 13

Spartan 57076-1

Бренд: Traxxas Страницы: 30

Бренд: Zoom Страницы: 24

Бренд: Zte Страницы: 16

Бренд: Garmin Страницы: 24

Бренд: LG Страницы: 42

Бренд: LG Страницы: 16

Бренд: LG Страницы: 20

Бренд: LG Страницы: 32

Бренд: LG Страницы: 20

Бренд: LG Страницы: 2

Бренд: Billion Страницы: 72

Бренд: Dr. Neuhaus Страницы: 2

Бренд: Datatronics Страницы: 116

Бренд: Elster Страницы: 8

Бренд: Ebyte Страницы: 35

Бренд: BT Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды