Raveon FireLine Ethernet Скачать руководство пользователя | Manualshive

Страница: 4 / 34

background image

Overview

The

FireLine

RF data radio is a rugged high-performance, high-speed narrow-

band data modem. It contains a receiver, a transmitter, and modem, creating
an easy-to-use transparent data radio link. The

FireLine’s

user interface is

asynchronous data into and out of the

FireLine

. Modem operation is virtually

transparent to the user and the configuration of the modem is via the user
serial port.

For privacy and network versatility, the

FireLine

incorporates a 16 bit

identification code. Its protocol also uses a 16bit CRC to guarantee the
integrity of the data. Perfect for SCADA and telemetry applications, the

FireLine

can be used for simple point-to-point data communication

applications, or for more sophisticated point-to-multipoint, peer-to-peer, or
mesh networks.

Although the

FireLine

is the easiest to use modem on the market, its re-

programmability makes it extremely versatile. Most parameters within the
modem may be re-configured to optimize it for specialized operations,
extended range, or higher data throughput.

FCC Safety Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

NOTE: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user’s authority to operate the equipment.

This product also complies with FCC Part 22 and Part 90 of the FCC rules
and regulations.

The Federal Communications Commission (FCC), with its action in ET Docket
93-62, has adopted a safety standard for human exposure to Radio
Frequency (RF) electromagnetic energy emitted by FCC-certified equipment.
This product meets the uncontrolled environmental limits as stated in OET-
65C (01-01) when operated in accordance with the operation guidelines
described in this manual. Proper operation of this radio device according to
the instructions in this publication will result in user exposure substantially
below the FCC recommended limits.

This equipment generates, uses, and radiates radio frequency energy, and if
not installed and used in accordance with the instructions, may cause harmful
interference. However, there is no guarantee that interference will not occur. If
this equipment does cause interference to radio or television reception, which

«
...
2
3
4
5
6
...
»

Содержание FireLine Ethernet



































Отзывы:

Нет отзывов

Похожие инструкции для FireLine Ethernet

Бренд: Radyne Страницы: 192

CommPlete MT3334HD8

Бренд: Multitech Страницы: 100

Бренд: FTS Страницы: 2

Бренд: US Robotics Страницы: 129

Бренд: Ebyte Страницы: 22

Бренд: XAVI Technologies Corp. Страницы: 59

Бренд: Billion Страницы: 1

Бренд: Fargo Страницы: 17

Бренд: Technicolor Страницы: 34

Бренд: Shuttle Страницы: 5

Бренд: Blonder tongue Страницы: 20

Бренд: Technicolor Страницы: 3

Бренд: Adeunis RF Страницы: 109

Бренд: NimbeLink Страницы: 8

Бренд: Kinpo Страницы: 24

Бренд: Bausch Datacom Страницы: 22

Бренд: Romtelecom Страницы: 46

SURFboard SBV3202

Бренд: CommScope Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды