Raveon FireLine Ethernet Скачать руководство пользователя

Страница: 25 / 34

Company Confidential

Raveon Technologies Corp.

SkyLine Compatibility Mode

General

The

FireLine

RF modem has built-in compatibility with a radio modem made

by Sonik Technologies, Vytek Wireless, and Cal Amp called the

SkyLine

. In

most applications, Raveon’s

FireLine

modem can communicate with

SkyLine

modems, provided the

FireLine

is properly configured.

Configuring FireLine to Communicate with a SkyLine

To configure the

FireLine

modem to talk to an old

SkyLine

modem, the user

must configure the

FireLine

with these commands:

ATMT 1

This command tells the

FireLine

modem to use a protocol that is

compatible with the

FireLine

. Note: ATMT 0 sets it back to the

FireLine

mode.

ATR2

This command tells the

FireLine

modem to operate with an over-

the-air baud rate of 5124 bits per second.  This is the baud-rate of
all narrow-band (12.5Khz spaced) SkyLine radio modems.
Wide-band SkyLine radios operated at 9600 baud over the air.
The command to set the

FireLine

to 9600 baud over the air is

ATR2 5.

ATR5

This command tells the

FireLine

modem to send 6 bytes of pre-

amble before every transmission.

MYID 1234

The MYID of the

FireLine

modem is set with the ATDT command

or the MYID command. The default MYID of the SkyLine was
1234.

TOID FFFF

The TOID of the

FireLine

modem is set with the ATMK command

or the TOID command. The default TOID of the SkyLine was
FFFF (broadcast address).

A quick-configure command is included in the

FireLine

, to allow it to be easily

switch to the

FireLine

mode. The command is “SKYLINE”. When in the

configuration mode, enter

SKYLINE

, and the modem will reconfigure itself as

a narrow-band SkyLine modem, with

TOID = FFFF

MYID=1234

, 80 byte

packets, 20mS serial port time out, channel 1 frequency, over-the-air baud
rate 5142.

SkyLine Compatibility Notes

The TOID and the MYID of the

FireLine

modem will both be the same Module

Address. If the TOID from a SkyLine transmitted packet matches the Module
Address of the

FireLine

, the

FireLine

will receive the data. Just as in the

SkyLine, the

FireLine

will use the FF character as a wild-card address filter.

Содержание FireLine Ethernet



































Результаты поиска

Содержание FireLine Ethernet

Отзывы:

Похожие инструкции для FireLine Ethernet

Бренды по названию

Популярные бренды

Raveon FireLine Ethernet, Техническое руководство

Результаты поиска

Содержание FireLine Ethernet

Отзывы:

Похожие инструкции для FireLine Ethernet

Бренды по названию

Популярные бренды