Raveon FireLine Ethernet Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 34

Raveon FireLine Ethernet Скачать руководство пользователя страница 30

Company Confidential

30

Raveon Technologies Corp.

(DB-9 Female shown. Same wiring for male-to-male cable)

Connector 1

Connector 2

Function

2

3

Rx

Tx

3

2

Tx

Rx

4

6

DTR

DSR

5

5

Signal ground

6

4

DSR

DTR

7

8

RTS

CTS

8

7

CTS

RTS

Compatibility issues

The null modem cable with full handshaking does not permit the older way of
flow control to take place. The main incompatibility is the cross connection of
the

RTS

and

CTS

pins. Originally, these pins are used for a question/answer

type of flow control. When the full handshaking null modem cable is used,
there is no request anymore. The lines are purely used for telling the other
side if communication is possible.

The main advantage of this cable is, that there are two signaling lines in each
direction. Both the

RTS

and

DTR

outputs can be used to send flow control

information to the other device. This makes it possible to achieve high
communication speeds with this type of null modem cable, provided that the
system has been designed for it.

«
...
28
29
30
31
32
...
»

Содержание FireLine Ethernet



































Отзывы:

Нет отзывов