manualshive.com logo in svg

Ravenheat HE 120N, Инструкция по использованию, установке и обслуживанию

Поделиться
Скачать
Ravenheat HE 120N Скачать руководство пользователя страница 44

Supplied By www.heating spares.co  Tel. 0161 620 6677

Fig. 97

Fig. 96

  IMPORTANT :Please,  
  lubricate the  internal 
  part  of the seals before 
  being fitted.

    

  

44

  
   Exhaust/suction system with concentric pipes for fl at or
   sloping roofs. Extensions with two separate pipes 
    ( Fig.95 ).

   Maximum distance : T= L = 21+21 = 42 metre+Terminal
   Minimum distance  : L = 0.5+0.5= Terminal

   Exhaust terminal must not be cut

   NOTE:
      - If bends are used in the exhaust fl ue then horizontal
      - sections must be avoided and there must be a 2° slope 
      - towards the  boiler 35 mm fall per metre.

   IMPORTANT:
   -  See Fig. 6 and 42 for terminal clearances.
   -  The pressure loss see  table 6.

   Exhaust/suction system with two separate rated 80 dia. 
   Pipes - exhaust on fl at or sloping roof, 
   suction from vertical wall  ( Fig.96 ).

   Maximum distance D = L + L1 =  40.5 metre + Terminal
   Minimum total length = 2 metre
   NOTE: Exhaust fl ue must slope 2° down towards the
               boiler 35  mm fall per metre.

   Exhaust/suction system with two separate
   pipes  through a single vertical wall ( Fig.97 ).

   Maximum distance : D = L + L1 = 37 metre
   Minimum distance  : D = L + L1 = 1 metre
   Min distance between pipe 50 mm.

 
   IMPORTANT NOTICE: 
   - inlet and exhaust terminals must never 
     be installed on opposite walls of the building  (PrEN 483).

- 

 If the fl ue terminates less than 2 m  above a balcony, above   

   the ground, or above  a fl at roof to which people have access,  
   then a suitable terminal guard must be fi tted.
-  Fit only recommended fl ue terminal guard by
   securing concentrically around terminal with screws.

  
  Available on request from:
  RAVENHEAT MANUFACTURING LTD
  Chartist Way,Morley, Leeds, West Yorkshire 
  ENGLAND  LS27 9ET - U.K.
  Tel. 0044(0) 113  252 7007

 11.1.2 

 11.1.3 

 11.1.4 

Содержание HE 120N




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды