Ravenheat HE 120N Скачать руководство пользователя страница 38

Страница: 38 / 51

Supplied By www.heating spares.co Tel. 0161 620 6677

8.23

TO REMOVE/REPLACE TIMECLOCK

8.23.1

Remove front casing (sect 8.1.4)

and lower the instrument panel .

8.23.2

Remove control board box cover.

8.23.3

Pull the two securing clip that fasten the
timeclock to the panel instrument,

and pull it out .

8.23.4

Carefully remove the four wires
connecting timer by pulling spade
connectors from timer

8.23.5

Replace in reverse order

NOTE: Ensure all electrical connections

are made correctly.

8.24 TO REMOVE/REPLACE CONTROL

BOARD (Fig.65).

8.24.1

Remove front casing (sect 8.1.4)

and lower the instrument panel .

8.24.2

Remove control board box cover.
(sect.8.13.1).

8.24.3

Detach the connectors from the board .

8.24.4

Detach the PCB board from its base by
unscrewing the four securing screws.

8.24.5

Replace in reverse order.

NOTE: When refitting the control panel

ensure the leads are not trapped.

8.25

TO REMOVE/REPLACE DIGITAL
DISPLAY BOARD (Fig.65).

8.25.1

Remove front casing (sect 8.1.4)

and lower the instrument panel .

8.25.2

Remove control board box cover.

8.25.3

Detach the connectors from the board.

8.25.4

Detach the Digital Display board from
panel instruments by unscrewing the four
securing screws.

8.25.5

Replace in reverse order.

Fig.65

Содержание HE 120N




















































Результаты поиска

Содержание HE 120N

Отзывы:

Бренды по названию

Популярные бренды

Ravenheat HE 120N, Инструкция по использованию, установке и обслуживанию

Результаты поиска

Содержание HE 120N

Отзывы:

Бренды по названию

Популярные бренды