Ravenheat HE 120N Скачать руководство пользователя страница 39

Страница: 39 / 51

Supplied By www.heating spares.co Tel. 0161 620 6677

8.26 TO REMOVE/REPLACE CONDENSING

TRAP (Fig.66).

8.26.1

Remove the casing (sect 8.1.4) and lower
the instrument panel .

8.26.2

Remove the securing clip and pull out the
plastic pipe that connect the condensing
trap at the heat exchanger.

8.26.3

Unscrew the nut that fasten the
condensing trap to the depression
chamber and remove it.

8.26.4

Replace in reverse order

Fig.67

8.28 TO REMOVE/REPLACE THE WATER

PRESSURE GAUGE (Fig. 67).

8.28.1

Remove front casing (sect 8.1.4)

lower

the instrument panel and remove
lower panel of the case.

8.28.2

Close the heating system on/off valves

and drain the water from the drain point
on the heating system .

8.28.3

Remove the retaining clip that secures the

pressure gauge probe.

8.28.4

Remove the pressure gauge from the

instrument panel by pressing its fastening
springs.

8.28.5

Replace in reverse order.

Fig.66

8.27

TO REMOVE/REPLACE THE MAIN

SWITCH (Fig. 67).

8.27.1

Remove front casing (sect 8.1.4) and lower

the instrument panel .

8.27.2

Remove the control box cover.

8.27.3

Pull off the switch knob. Remove

the switch out from the instrument panel
by pressing the clamp springs .

8.27.4

Detach the wires that connect to the

switch, make sure that these wires are
later reconnected to the same poles .

8.27.5

Replace in reverse order

Содержание HE 120N




















































Результаты поиска

Содержание HE 120N

Отзывы:

Бренды по названию

Популярные бренды

Ravenheat HE 120N, Инструкция по использованию, установке и обслуживанию

Результаты поиска

Содержание HE 120N

Отзывы:

Бренды по названию

Популярные бренды