manualshive.com logo in svg

Ravenheat 780 Series, Инструкция по использованию, установке и обслуживанию

Поделиться
Скачать
Ravenheat 780 Series Скачать руководство пользователя страница 41

       

      

BOILER NOT OPERATIONAL ON TIMER (INTEGRAL)

     
   

 Switch on/select  “Winter” / Central heating.

     Stat to Maximun/Ensure External control calling for heat (Room Stat / TRV).           

   
   

Is Timer set to 

   “OFF” ?

 

 Set Timer to Required 
 mode - Recheck

 Yes

  No

  Yes

 Yes

  No

  Yes

  Yes

  Yes

 No

 
 

Timer set to 

 “AUTO” ?

  No

  No

  No

 

 Check programme are 
 setting Correct

 
 Timer set to “ON” ?

 

 Timer set to “AUTO”

 
 Does neon on   
 Timer illuminate?

 

 Are L and N connections 
 to points 1 and 2 ?

  Yes

 

 Is there 230V across 
 point 1 and 2 ?

 

  
   Are L and N correctly ?

 

  Electrical fault within 
  boiler ?
   

  No

  

  
       TIMER FAULT

 
 With leads disconnected, is there 
 continuity across leads to 3 and 5 ?

   Enter correct programme   
   as per instructions provided. 
   Recheck.

  No

 
 With leads connected, is there continuity 
 across leads to 3 and 5 ?

  No

  

  Is there continuity 
 across internal fuse ?

 

  
       Change fuse
   

 
 External Control fault - Check.

  Yes

  

  Electrical fault within 
  boiler.

  Yes

      

41

Содержание 780 Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды