Ravenheat 780 Series Скачать руководство пользователя | Manualshive

Страница: 24 / 52

background image

Fig. 34

24

5.11 SAFETY VALVE DISCHARGE AND

CONDENSATE DRAIN CONNECTION.

5.11.1

The safety valve is located on the return

manifold.The discharge should terminate
facing downward exterior to the building in a
position where discharging (possibly boiling
water & steam) will not create danger or
nuisance, in a easily visible position, not to
cause damage to electrical components or
wiring.

The discharge must not be over an entrance
or a window or any other type of access.

5.12 ELECTRICAL

CONNECTIONS

5.12.1 IMPORTANT:

Electricity supply must be as

specified in clause (sect. 4.10).

- When controls external to the appliance

are required, design of the external
electrical circuits should be undertaken by
a competent person. In accordance with the
IEE wiring regulations.

It is essential that all external controls

must be volt free.

Factory fitted internal wiring must not be

disturbed when wiring external controls.

- There are the control board, where the

terminals are easily visible in fig. 36, and
the terminal board (fig. 1) whwre to connect
the cylinder thermostat and the diverter
valve (fig. 36/a).

-

Heat resistant flexible cable is fitted
between the isolator and the terminal block
A 3 core cable of 0.75 mm

2

(24x0,2 mm) to

BS 6500.

Make sure all wires to the appliance are

routed away from sharp edges and hot
surfaces.

The cable must be fastened with its cord

anchorage and connected so that should the
cable slip from the anchorage the current
carrying conductors becomes taut before
the earthing conductor. Securely tighten all
terminal screws and arrange the cable with
slack between the cord anchorage and the
terminal block.

WARNING: If the supply cord is damaged,

it must be replaced by a service engineer
(supply cord available from Ravenheat
Manufacturing Ltd).

5.11.2

The condensate drain connection is on the
left of Gas service cock (Fig.34).

A 25 mm plastic overflow pipe is fitted on

the condensing trap and should be used
to fit on the drain connection, if required,
to discharge condensate to a drain. The
drain pipe should have a fall of a least 2.5°
away from the boiler. Condensate should, if
possible be discharged into the household
internal drainage system.

If this is not practicable, discharge can be

allowed into the external household drains
or a purpose designed soak away.

It is recommended that any external

condensate drain pipe is insulated and also

preferably of 32 mm diameter, to prevent

freezing in adverse weather conditions.

The condensate is discharged periodically
in “ slugs” by siphonic action. It is not

necessary to provide air breaks or extra
traps in the discharge pipe as there is
already a 125mm high trap inside the boiler.

Fitting an extra trap may cause the boiler

siphon to work incorrectly.

Refer to BS5546 or BS6798 for advice on

disposal of boiler condensate.

«
...
22
23
24
25
26
...
»

Содержание 780 Series





















































Отзывы:

Нет отзывов

Похожие инструкции для 780 Series

Vitocrossal 200 CM2 Series

Бренд: Viessmann Страницы: 100

Бренд: Alde Страницы: 8

Бренд: EASCO Страницы: 46

Бренд: Alpha Boilers Страницы: 36

Бренд: TriangleTube Страницы: 32

thermodual tda 30

Бренд: Euroheat Страницы: 48

Бренд: THERMOSTAHL Страницы: 29

Бренд: Thermona Страницы: 37

ZB 7-28 R 28 HE

Бренд: Benchmark Страницы: 48

HE COMBI EXTERNAL

Бренд: Immergas Страницы: 32

Бренд: Immergas Страницы: 40

MAGIS VICTRIX ERP

Бренд: Immergas Страницы: 48

Бренд: Palazzetti Страницы: 140

Бренд: Ideal Boilers Страницы: 8

Бренд: Weil-McLain Страницы: 40

Бренд: HDG Страницы: 88

Бренд: thermital Страницы: 8

Бренд: Wolf Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды