Ravenheat 780 Series Скачать руководство пользователя

Страница: 35 / 52

7.14.3

Remove the switch out from the instrument

panel by pressing the clamp springs.

7.14.4

Replace in reverse order.

7.11

TO REMOVE/REPLACE THE INJECTORS

( fi g. 50).

7.11.1

Remove the front casing and the depression
chamber front cover (sect.7.3 - 7.4).

7.11.2

Unscrew the union and the 4 screws securing
the manifold at the burner.

7.11.4

Pull the manifold up and out from the
combustion chamber.

7.11.5

Unscrew and replace the injectors and their

seals.

7.11.6

Replace in reverse order.

7.11.7

Relocate the grommet, sealing the gas supply

pipe to the casing taking care not to damage

it. Replace if necessary.

7.12

TO REMOVE/REPLACE THE BURNER

7.12.1

Remove front casing (sect.7.3) and the

combustion chamber front cover (sect.7.4).

7.12.2

Remove the injectors manifold as described

in sect. 7.11.

7.12.3

Remove the two screws securing the main

burner to the combustion chamber.

7.12.4

Pull the burner forward and remove (fig. 49).

7.12.5

Replace in reverse order.

IMPORTANT:

When refitting the burner make

sure that the pins at the rear of the combustion

chamber locate into the slots made on the rear

of the burner.

7.13

TO REMOVE/REPLACE THE GAS VALVE .

7.13.1

Remove front casing (sect.7.3) and the

combustion chamber front cover (sect.7.4).

7.13.2

Unscrew the union.

7.13.3

Remove the 2 screws to the gas pipeline.

7.13.4

Remove the eight screws (four per side) that

connect the gas valve to the gas pipelines and

then remove it from its seat.

7.13.5

Replace in reverse order, always using new seals.

7.14

TO REMOVE/REPLACE THE MAIN

SWITCH (fig. 35).

7.14.1

Remove front casing (sect. 7.3) and remove

the panel instrument.

7.14.2

Detach the wires that connect to the switch.

7.15 TO REMOVE/REPLACE THE HEATING
SENSOR.

7.15.1

Remove front casing (sect. 7.3).

7.15.2

Remove the wires that connect the sensors.

7.15.3

For C.H. thermistor remove the retaining clip

from the pipe.

Replace in reverse order.

7.16

TO REMOVE/REPLACE THE OVERHEAT

THERMOSTAT.

7.16.1

Remove front casing (sect. 7.3).

7.16.2

Remove the two wires that connect to the

overheat

thermostat.

7.16.3

Remove the two screws securing the thermo-

stat to the pipe and pull it out.

7.16.4

Replace in reverse order.

Содержание 780 Series





















































Результаты поиска

Содержание 780 Series

Отзывы:

Похожие инструкции для 780 Series

Бренды по названию

Популярные бренды

Ravenheat 780 Series, Инструкция по использованию, установке и обслуживанию

Результаты поиска

Содержание 780 Series

Отзывы:

Похожие инструкции для 780 Series

Бренды по названию

Популярные бренды