Ravenheat 780 Series страница 37 Скачать руководство пользователя

Страница: 37 / 52

7.18 TO REMOVE/REPLACE THE WATER

PRESSURE GAUGE (Fig. 54).

7.18.1

Remove front casing (sect 7.3).

7.18.2

Close the on/off valves for the heating

circuit and drain the water.

7.18.3

Unscrew the fitting that secures the

pressure gauge probe.

7.18.4

Remove the pressure gauge from the

instrument panel by pressing its fastening
springs.

7.18.5

Replace in reverse order.

New seal must be used.

7.19 TO REMOVE/REPLACE THE ELECTRIC

CONTROL AND IGNITION BOARD.

7.19.1

Remove the front panel from the outer
casing (sect. 7.3) and lower the instrument

panel .

7.19.2

Unscrew the 2 screws holding the control box

box cover and remove.

Disconnect mains cables and any other
connections (room thermostat).

7.19.3

Detach the connectors from the board.

7.19.4

Replace in reverse order (ensure all electrical

connections are made correctly).

7.17

TO REMOVE/REPLACE THE DIFFERENTIAL
PRESSURE SWITCH (fig. 52).

7.17.1

Remove front casing (sect. 7.3).

7.17.2

Detach the wire connector plug from the

pressure switch, make sure that the wire
connector plug are later reconnected.

7.17.3

Unscrew the two screws that fasten the pressure

switch to the back of the combustion

chamber.

7.17.4

Remove the two silicone tubes.

7.17.5

Ensure tubes are connected correctly (Fig. 52)

avoiding kinks.

7.17.6

Replace in reverse order ensuring that the

“

–”

tapping is connected to the tube

terminating inside the case and the “+”
tapping is connected to the tube terminating at

the flue ring.

Fig. 53

Fig. 54

Fig. 52

Содержание 780 Series





















































Результаты поиска

Содержание 780 Series

Отзывы:

Похожие инструкции для 780 Series

Бренды по названию

Популярные бренды

Ravenheat 780 Series, Инструкция по использованию, установке и обслуживанию

Результаты поиска

Содержание 780 Series

Отзывы:

Похожие инструкции для 780 Series

Бренды по названию

Популярные бренды