Raven Sidekick Pro Скачать руководство пользователя страница 58

Страница: 58 / 64

CHAPTER 7

SideKick Pro™ ICD 1-40 oz./min. and 5-200 oz./min. Installation & Operation Manual

DIAGNOSTIC TROUBLE CODES (DTCS)

TABLE 2.

Diagnostic Trouble Codes

Code ID

Description

Recommended Actions

523152

Invalid pump state

Verify the communication setup/

shutdown alarm.

523154

Lost communication

Verify the communication setup/

shutdown alarm.

Target flow too high

1. Reduce the equipment speed.
2. Reduce the target application rate.

Target flow too low

1. Increase the equipment speed.
2. Increase the target application rate.

523160

Chemical tank is empty

Refill the product to continue field

applications.

Low tank volume remaining

Refill the product to continue field

applications.

523167

Injection pressure sensor

disconnected

1. Verify good connection to the pressure

sensor on the pump.

2. Verify the sensor is getting supply voltage.
3. Verify the signal voltage is getting back to

the pump ECU.

High injection pressure

1. Verify the communication setup/shutdown

alarm.

2. Check for an obstruction in the injection

system discharge hose.

3. Verify the carrier pressure is not exceeding

150 PSI.

523169

Low motor voltage

1. Verify high current breaker is not tripped.
2. Verify battery connections.
3. Verify speed sensor and signal. Refer to

the field computer operation manual for

information on testing speed and flow

cabling and troubleshooting the speed

sensor.

Содержание Sidekick Pro
































































Результаты поиска

Содержание Sidekick Pro

Отзывы:

Бренды по названию

Популярные бренды

Raven Sidekick Pro, Руководство по установке и эксплуатации

Результаты поиска

Содержание Sidekick Pro

Отзывы:

Бренды по названию

Популярные бренды