background image

 

 

PAGE 14/36 |

 Installation manual 

|

 016-8000-028EN 

|

 Rev. B

 

Raven Industries Inc.

 

CRX/ ROS INSTALLATION | CRX/VIPER 4+ ROS - RS1 | RAVEN EUROPE GENERIC 

1.2.2

 

HYDRAULIC INSTALLATION LOAD SENSE 

The manifold should be connected between the hoses 
leading from the steering orbitrol to the steering 
cylinder(s). To do so, the hoses should be 
disconnected, preferably on an existing connection 
between a pipe line and a hose. 

Connect the hoses from the steering orbitrol to 

A1

 

and 

B1

 on the manifold. Connect the hoses to the 

steering cylinders to 

and 

B

 on the manifold (Figure 5 

and Figure 6). 

Connect the pressure line, return line and the LS line of 
the hydraulic pump to the 

P

T

 and 

LS

 of the manifold. 

When needed refer to the hydraulic diagram of the 
tractor to find the correct connections on the tractor. 

Caution!:

 

 

 

 

   

If there are separate hydraulic systems with 
separate oil tanks on the tractor, the manifold 
must be connected to the system in which the 
steering orbitrol and steering cylinder are 
included in.

 

Hint!:   

 

 

 

       

Mark the lines twice with 'A' and 'B', before 
disconnecting them 

 

1.2.3

 

CONNECTING THE SHUTTLE VALVE 

A shuttle valve must be installed in the load sense line. 
See Figure 7 for proper mounting and orientation of 
the shuttle valve. This way, when in rest, the ball floats 
inside the valve, which will benefit the response for the 
load sense signal. In addition, it is important that the 
shuttle valve is installed as close to the pump as 
possible. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Steering Cylinder(s) 

FIGURE 5 LOAD SENSE CONNECTING CIRCUIT

 

FIGURE 6 CONNECTIONS FOR THE HYDRAULIC 
LOAD SENSE MANIFOLD

 

Signal from 
manifold 

Signal from 
other users 

Signal to LS-
pump 

FIGURE 7 TOP VIEW OF SHUTTLE VALVE FOR 
MOUNTING IN THE LOAD SENSE LINE

 

 

Содержание CRX ROS+RS1





































Отзывы: