Raven CRX ROS+RS1 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 36

background image

PAGE 12/36 |

Installation manual

|

016-8000-028EN

|

Rev. B

Raven Industries Inc.

CRX/ ROS INSTALLATION | CRX/VIPER 4+ ROS - RS1 | RAVEN EUROPE GENERIC

•

If necessary the positive and negative wires, in
between the battery and the fuses, can be
shortened. Be sure to use cable sockets with
the correct size for proper connection.

•

If a ground switch is used in the tractor,
connect the wiring harness behind the ground
switch (not at the battery side of the ground
switch!).

•

If a main (12V) switch is used in the tractor, the
red wire connect the wiring harness behind the
main switch (not at the battery side of the
main switch!).

•

If no main switch is used, always connect the
wiring harness directly to the battery.

•

If the system is connected to a 24 Volt
machine, always use a 24V to 12V converter.
Never connect between the two batteries of a
24V machine!

•

Lead the terminal harness along with the GPS
and radio/GSM antenna cables through one
pillar of the cab.

•

Tie-wrap the harnesses so they are attached
free from vibration and friction.

Caution!:

It is important to ensure that the wiring harness
is always connected to the battery AFTER
installing all wires and controllers!

«
...
10
11
12
13
14
...
»

Содержание CRX ROS+RS1





































Отзывы:

Нет отзывов

Похожие инструкции для CRX ROS+RS1

Бренд: Masalta Страницы: 13

Raven OMNiPOWER NL5000 G5

Бренд: New Leader Страницы: 268

Monster Truck Headboard 41903

Бренд: Simplay3 Страницы: 4

Бренд: Kongsberg Страницы: 188

Бренд: Proactive Страницы: 14

Бренд: sauter Страницы: 5

Бренд: Trigano Страницы: 13

Бренд: Berner Страницы: 30

Бренд: Kitagawa Страницы: 32

Бренд: endolite Страницы: 158

Бренд: Lupine Страницы: 7

Spectral M950 Q4 Tour

Бренд: SHOWTEC Страницы: 24

Бренд: Ibiza Страницы: 20

Бренд: ZOE Страницы: 40

Бренд: National Instruments Страницы: 4

Z62-H370.01 S5W2

Бренд: Jäger Страницы: 36

ThermoStable SOV-20

Бренд: Daihan Scientific Страницы: 43

Бренд: qeedo Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды