Rasonic RC-S70U, Руководство по эксплуатации и инструкция по установке

Страница: 26 / 44

•
4
ELECTRICAL WARNINGS
•
Only use the specified power cord. If the power cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
Keep power plug clean. Remove any dust or grime that accumulates on or around the plug. Dirty plugs can cause fire
or electric shock.
Do not
pull power cord to unplug unit. Hold the plug firmly and pull it from the outlet. Pulling directly on the cord can
damage it, which can lead to fire or electric shock.
Do not
modify the length of the power supply cord or use an extension cord to power the unit.
Do not
share the electrical outlet with other appliances. Improper or insufficient power supply can cause fire or electrical
shock.Always install circuit breaker and a dedicated power circuit.
Do not
use the socket if it is loose or damaged.
Do not
place heavy object on the power cord and ensure that the cord is not compressed.
There is danger of fire or electric shock.
If water enters the unit, turn the unit off at the power outlet and switch off the circuit breaker.
Isolate supply by taking the power-plug out or disconnect the power supply to the unit, contact a qualified service
technician.
The product must be properly grounded at the time of installation, or electrical shock may occur.
For all electrical work, follow all local and national wiring standards, regulations, and the Electrical Connection Diagram
located on the top panel of the unit.
If connecting power to fixed wiring, an all-pole disconnection device which has at least 3mm clearances in all poles,
and have a leakage current that may exceed 10mA, the residual current device(RCD) having a rated residual operating
current not exceeding 30mA, and disconnection must be incorporated in the fixed wiring in accordance with the wiring
rules.
This unit is earthed through the power cord, make sure that the unit is correctly grounded. The wall outlet(Air-break
switch) should be provided with reliable earth wire.
The unit should be provided with an individual circuit and the circuit breaker/fuse rating should be the same as that
of the power cord and wall outlet. Power cord conductors are distinguished according to the color as shown in Wiring
Diagram located on the top of the machine.
WARNINGS FOR PRODUCT INSTALLATION
1. Installation must be performed by an authorized dealer or specialist. Defective installation can cause water leakage,
electrical shock, or fire.
2. Installation must be performed according to the installation instructions. Improper installation can cause water leakage,
electrical shock, or fire.
3. Contact an authorized service technician for repair or maintenance of this unit. This appliance shall be installed in acc-
ordance with national wiring regulations.
4. Only use the included accessories, parts, and specified parts for installation. Using non-standard parts can cause water
leakage, electrical shock, fire, and can cause the unit to fail.
5. Install the unit in a firm location that can support the unit’s weight. If the chosen location cannot support the unit’s
weight, or the installation is not done properly, the unit may drop and cause serious injury and damage.
6. Install drainage piping according to the instructions in this manual. Improper drainage may cause water damage to your
home and property.
7. For units that have an auxiliary electric heater, do not install the unit within 1 meter (3 feet) of any combustible materials.
8.
Do not
install the unit in a location that may be exposed to combustible gas leaks. If combustible gas accumulates aro-
und the unit, it may cause fire.
9.
Do not
turn on the power until all work has been completed.
10. When moving or relocating the air conditioner, consult experienced service technicians for disconnection and reinsta-
llation of the unit.
11. How to install the appliance to its support, please read the information for details in "Installation instructions" section.
TAKE NOTE OF FUSE SPECIFICATIONS
Wall outlet
Air-break switch
The air conditioner’s circuit board (PCB) is designed with a fuse to provide overcurrent
protection. The specifications of the fuse are printed on the circuit board ,such as
220V
.
•
•
•
•
•
•
•
•
•
•
•
•