background image

 
 
Hardware Installation 

PixelStor 300e Hardware Installation Manual   
Rev. 1, May 2013 

2-9 

300e to an existing system, the PS300e must be the last enclosure in the daisy chain.   

 

PixelStor 300e 

enclosures follow the same concept of “disk groups” used for the PixelStor 5000. 

A “disk group” (DG) is composed of an associated group of disks with similar RAID properties. All 
DGs must be assigned a RAID level. The system supports RAID 0, 1,5,10. The following rules 

must be followed when creating DGs for a PixelStor 5000/PS300e: 

 

 

 

A DG can span across interconnected PixelStor 5000 and PixelStor 300e systems.   

 

Drives within a DG can reside in any order across any of the enclosures in a system. 

 

Capacity of a DG can be expanded by adding disks from the available pool of global spare 
disks. (Adding disks to a disk group may require multiple disks.)   

 

DGs can be accessed by either controller, but must be assigned a primary controller. 

 

Drives not assigned to a disk g

roup will be classified as “Global Spares” 

 

Global spare(s) can reside on any of the 4 interconnected chassis to protect any DG within 
the four chassis. A Global Spare cannot be added to RAID 0 DG. 

 

Failed Disks or disks disassociated from their disk group w

ill be classified as “Orphans” by the 

system. 

 

It is recommended not to build a RAID 5 DG beyond 8 drives. The bigger the RAID 5 DG, the 
higher the probability for multi-drive failures. Multi-drive failure is not protected by RAID 5. 

 

To build RAID 5 DG bigger than 8 drives, use the systems capacity expansion feature to 
concatenate a second RAID 5 disk group to the first. You can do this multiple times up to a 

maximum of 24 drives. 

 

Disk Group (DG) Parameters 

RAID 0               

RAID 5 

RAID 1 

RAID 1+0 

1.

 

Minimum # of Drives per DG 

2     

4   

2.

 

Maximum # of Drives per DG 

Capacity 

24 

24 

24 

24 

3.

 

DGs Allowed per System 

1-4 

1-4 

1-4 

1-4 

4.

 

RAID Level Allowed per DG 

5.

 

Drives Must be Added in 

Singles 

Singles 

Pairs 

Pairs 

6.

 

Global Spare Capability 

N/A 

Yes 

Yes 

Yes 

7.

 

Access DG by both Controllers 

Yes 

Yes 

Yes 

Yes

 

 

To improve the utilization of the available storage capacity and ensure reliability, it is 

recommended that all disk drive modules within a DG be the same size and from the 

same manufacturer. This is because for each RAID Group, the system scales down     

to the size of the smallest drive (except for RAID 0). 

Содержание PixelStor 300e












































Отзывы: