manualshive.com logo in svg

Rasilient PixelStor 300e, Руководство по установке оборудования, Страница: 27 / 43

Поделиться
Скачать
Rasilient PixelStor 300e Скачать руководство пользователя страница 27

 
 
Hardware Installation 

PixelStor 300e Hardware Installation Manual   
Rev. 1, May 2013 

2-1 

2

 

Hardware Installation 

This chapter describes the hardware setup procedures that you have to perform when removing 

or replacing system components. The PS300e is designed with tool less modules which allow 

users to remove or install modules without any tools. The tool less modules are listed below: 

 

 

SAS IO Modules 

 

Power Supply Modules 

 

Fan Modules 

 

Mid-plane 

 

Hard Drives 

2.1 

SAS IO Modules 

This PS300e is designed to operate with up to two SAS IO modules. When the PS300e is 

equipped with dual SAS IO modules, the hot-swappable redundant function is enabled. If one 

SAS IO module fails, you can replace the failed SAS IO module without powering off the PS300e, 

because the surviving IO module takes the place of the failed one. 

 

The PS300e SAS IO modules are designed to be hot pluggable. They fit into one of the two IO 

module slots of the PixelStor 300e. The PS300e SAS IO modules contain firmware that initializes 

and configures various onboard devices and registers on the IO module. Figure 2-1    SAS IO 

Module Front Panel - shows the front panel of a SAS IO module.     

 

 

Figure 2-1    SAS IO Module Front Panel 

 

 

 

 

 

Features: 

 

 

Two (x4), 12Gbps SAS connectors - the left SAS connectors is configured for SAS OUT (

 

downstream connectors). The right SAS connector is configured SAS IN (

 upstream 

Содержание PixelStor 300e












































Отзывы:

Нет отзывов