Ranger 191 CAYMAN Скачать руководство пользователя

Страница: 36 / 78

Key Locks, Carpet, and Upholstery

CLEANING MARINE VINYL

For general purpose cleaning, use Vinyl Finish Vinyl Cleaner,

Fantastik, or warm water with a mild dish soap such as Dawn or Ivory.
Gently scrub with a small soft bristle brush.

For dirt build-up, use Vinyl Finish Vinyl Cleaners. Let soak for

approximately 10 minutes, then gently scrub with a soft bristle brush. For
specific stain removal, refer to the chart on page 36 or the staining agent’s
stain removal instructions.

USE

DO NOT USE

Vinyl Finish Vinyl Cleaner

Formula 409

Dish Soap (Dawn, Ivory)

Murphy’s Oil Soap

Fantastik

Simple Green

303 Protectant

DC Plus
ArmorAll
Top Kote Sealant
Son-of-a-Gun
Orange 88 Degreaser
Roll-Off
Bleach/Baking Soda
Turtle Wax Tar Remover
APCO
Harbor Mate

Certain household cleaners, powdered abrasives, steel wool, and

industrial cleansers can cause damage and discoloration and are not
recommended.

Dry cleaning fluids and lacquer solvents/acetone (for example, nail

polish remover) should not be used as they will remove printed pattern
and/or gloss.

Waxes should be used with caution as many contain dyes or solvents

that can permanently damage the protective coating.

DO NOT

use Formula 409 (the bottle

states the product should not be used on

vinyl.)

DO NOT

use kerosene, gasoline, or acetone, as they will remove the

protective marine top coat on your vinyl.

DO NOT

use any silicone based protectants. They will extract the

plasticizers, leaving the vinyl hard and brittle, and eventually cracking
will occur.

CAUTION

▲

Содержание 191 CAYMAN















































































Результаты поиска

Содержание 191 CAYMAN

Отзывы:

Похожие инструкции для 191 CAYMAN

Бренды по названию

Популярные бренды

Ranger 191 CAYMAN, Руководство пользователя

Результаты поиска

Содержание 191 CAYMAN

Отзывы:

Похожие инструкции для 191 CAYMAN

Бренды по названию

Популярные бренды